diff options
Diffstat (limited to 'thirdparty/STM32_USB-FS-Device_Lib_V4.0.0/Projects/Custom_HID/readme.txt')
-rw-r--r-- | thirdparty/STM32_USB-FS-Device_Lib_V4.0.0/Projects/Custom_HID/readme.txt | 177 |
1 files changed, 177 insertions, 0 deletions
diff --git a/thirdparty/STM32_USB-FS-Device_Lib_V4.0.0/Projects/Custom_HID/readme.txt b/thirdparty/STM32_USB-FS-Device_Lib_V4.0.0/Projects/Custom_HID/readme.txt new file mode 100644 index 0000000..b627219 --- /dev/null +++ b/thirdparty/STM32_USB-FS-Device_Lib_V4.0.0/Projects/Custom_HID/readme.txt @@ -0,0 +1,177 @@ +/** + ****************************************************************************** + * @file readme.txt + * @author MCD Application Team + * @version V4.0.0 + * @date 21-January-2013 + * @brief Description of the USB Custom_HID Demo. + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT 2013 STMicroelectronics</center></h2> + * + * Licensed under MCD-ST Liberty SW License Agreement V2, (the "License"); + * You may not use this file except in compliance with the License. + * You may obtain a copy of the License at: + * + * http://www.st.com/software_license_agreement_liberty_v2 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an "AS IS" BASIS, + * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + * + ****************************************************************************** + */ + + +Example description +=================== +This Demo provides a description of how to use the USB-FS-Device on the STM32F10xxx, +STM32F37xxx, STM32F30xxx and STM32L15xxx devices. +The STM32 device is enumerated as HID compliant device, that uses the native PC +Host USB-FS-Device HID driver. + +To test the example, you need to: + + 1)- Start the "USB HID Demonstrator" PC applet and connect STM32 USB to PC + 2)- The device should be detected and shown in the USB HID target box + 3)- Press Graphic View button + 4)- You can Select "use SET_FEATURE" or "use SET_REPORT" in order to use SET_REPORT request to send HID Report + for LED control + 5)- Make sure that following report ID are configured: LED1 ID (0x1) , LED2 ID(0x2), + LED3 ID(0x3), LED4 ID(0x4), and BUTTON1_ID(0x5) + 6)- Select Leds to switch on/off on the EVAL board => a SET_REPORT request will be sent + +More details about this Demo implementation is given in the User manual +"UM0424 STM32F10xxx USB development kit", available for download from the ST +microcontrollers website: www.st.com/stm32 + + +Directory contents +================== + + \inc: contains the Demo firmware header files + + \EWARM: contains preconfigured projects for EWARM toolchain + + \RIDE: contains preconfigured projects for RIDE toolchain + + \MDK-ARM: contains preconfigured projects for MDK-ARM toolchain + + \TASKING: contains preconfigured projects for TASKING toolchain + + \TrueSTUDIO: contains preconfigured projects for TrueSTUDIO toolchain + + \src: contains the Demo firmware source files + +Hardware environment +==================== +This example runs these STMicroelectronics evaluation boards and can be easily tailored to any other hardware: + +- STM3210B-EVAL +- STM3210E-EVAL +- STM32L152-EVAL +- STM32F373C_EVAL +- STM32F303C_EVAL +- STM32L152D-EVAL + +To select the STMicroelectronics evaluation board used to run the example, uncomment +the corresponding line in platform_config.h file. + + - STM3210B-EVAL Set-up + - Jumper JP1 (USB disconnect) should be connected in position 2-3. + + - STM3210E-EVAL Set-up + - Jumper JP14 (USB disconnect) should be connected in position 2-3. + + - STM32L152-EVAL Set-up + - Jumpers JP18 and JP19 should be connected. + - Jumper JP17 should be connected in position 5-6 (PB12 connector) + - Note that JoySitck Right and Left buttons are used for this Demo. + + - STM32L152D-EVAL Set-up + - LCD Glass should be mounted On IO position for Potentiometer usage. + - JP13 should be connected to ADC input. + + - STM32F373C_EVAL Set-up + - None. + + - STM32F303C_EVAL Set-up + - None. + +How to use it +============= + + EWARM + - Open the Custom_HID.eww workspace. + - In the workspace toolbar select the project config: + - STM3210B-EVAL: to configure the project for STM32 Medium-density devices + - STM3210E-EVAL: to configure the project for STM32 High-density devices + - STM3210E-EVAL_XL: to configure the project for STM32 XL-density devices + - STM32L152-EVAL: to configure the project for STM32 Medium-Density Low-Power devices + - STM32L152D-EVAL: to configure the project for STM32 High-Density Low-Power devices + - STM32373C-EVAL: to configure the project for STM32F37xxx devices + - STM32303C-EVAL: to configure the project for STM32F30xxx devices + - Rebuild all files: Project->Rebuild all + - Load project image: Project->Debug + - Run program: Debug->Go(F5) + + + MDK-ARM + - Open the Custom_HID.Uv2 project + - In the build toolbar select the project config: + - STM3210B-EVAL: to configure the project for STM32 Medium-density devices + - STM3210E-EVAL: to configure the project for STM32 High-density devices + - STM3210E-EVAL_XL: to configure the project for STM32 XL-density devices + - STM32L152-EVAL: to configure the project for STM32 Medium-Density Low-Power devices + - STM32L152D-EVAL: to configure the project for STM32 High-Density Low-Power devices + - STM32373C-EVAL: to configure the project for STM32F37xxx devices + - STM32303C-EVAL: to configure the project for STM32F30xxx devices + - Rebuild all files: Project->Rebuild all target files + - Load project image: Debug->Start/Stop Debug Session + - Run program: Debug->Run (F5) + + + RIDE + - Open the Custom_HID.rprj project. + - In the configuration toolbar(Project->properties) select the project config: + - STM3210B-EVAL: to configure the project for STM32 Medium-density devices + - STM3210E-EVAL: to configure the project for STM32 High-density devices + - STM3210E-EVAL_XL: to configure the project for STM32 XL-density devices + - STM32L152-EVAL: to configure the project for STM32 Medium-Density Low-Power devices + - STM32L152D-EVAL: to configure the project for STM32 High-Density Low-Power devices + - STM32373C-EVAL: to configure the project for STM32F37xxx devices + - STM32303C-EVAL: to configure the project for STM32F30xxx devices + - Rebuild all files: Project->build project + - Load project image: Debug->start(ctrl+D) + - Run program: Debug->Run(ctrl+F9) + + + TASKING + - Open TASKING toolchain. + - Click on File->Import, select General->'Existing Projects into Workspace' + and then click "Next". + - Browse to TASKING workspace directory and select the project: + - STM3210B-EVAL: to configure the project for STM32 Medium-density devices + - STM3210E-EVAL: to configure the project for STM32 High-density devices + - STM3210E-EVAL_XL: to configure the project for STM32 XL-density devices + - STM32L152-EVAL: to configure the project for STM32 Medium-Density Low-Power devices + - STM32L152D-EVAL: to configure the project for STM32 High-Density Low-Power devices + - STM32373C-EVAL: to configure the project for STM32F37xxx devices + - STM32303C-EVAL: to configure the project for STM32F30xxx devices + - Rebuild all project files: Select the project in the "Project explorer" + window then click on Project->build project menu. + - Run program: Select the project in the "Project explorer" window then click + Run->Debug (F11) + + + TrueSTUDIO + - Open the TrueSTUDIO toolchain. + - Click on File->Switch Workspace->Other and browse to TrueSTUDIO workspace + directory. + - Click on File->Import, select General->'Existing Projects into Workspace' + and then click "Next". + - Browse to the TrueSTUDIO workspace directory and select the project: + - STM3210B-EVAL: to load the project for STM32 Medium-density devices + - STM3210E-EVAL: to load the project for STM32 High-density devices + - STM3210E_EVAL_XL: to load the project for STM32 XL-density devices + - STM32L152_EVAL: to load the project for STM32 Medium-Density Low-Power devices + - STM32L152D-EVAL: to configure the project for STM32 High-Density Low-Power devices + - STM32373C-EVAL: to configure the project for STM32F37xxx devices + - STM32303C-EVAL: to configure the project for STM32F30xxx devices + - Rebuild all project files: Select the project in the "Project explorer" + window then click on Project->build project menu. + - Run program: Select the project in the "Project explorer" window then click + Run->Debug (F11) + +************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****** |