1 files changed, 121 insertions, 0 deletions
diff --git a/thirdparty/STM32_USB-FS-Device_Lib_V4.0.0/Projects/Device_Firmware_Upgrade/inc/usb_conf.h b/thirdparty/STM32_USB-FS-Device_Lib_V4.0.0/Projects/Device_Firmware_Upgrade/inc/usb_conf.h
new file mode 100644
index 0000000..d997e04
--- /dev/null
+++ b/thirdparty/STM32_USB-FS-Device_Lib_V4.0.0/Projects/Device_Firmware_Upgrade/inc/usb_conf.h
@@ -0,0 +1,121 @@
+/**
+  ******************************************************************************
+  * @file    usb_conf.h
+  * @author  MCD Application Team
+  * @version V4.0.0
+  * @date    21-January-2013
+  * @brief   Device Firmware Upgrade (DFU) configuration file
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; COPYRIGHT 2013 STMicroelectronics</center></h2>
+  *
+  * Licensed under MCD-ST Liberty SW License Agreement V2, (the "License");
+  * You may not use this file except in compliance with the License.
+  * You may obtain a copy of the License at:
+  *
+  *        http://www.st.com/software_license_agreement_liberty_v2
+  *
+  * Unless required by applicable law or agreed to in writing, software 
+  * distributed under the License is distributed on an "AS IS" BASIS, 
+  * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+  * See the License for the specific language governing permissions and
+  * limitations under the License.
+  *
+  ******************************************************************************
+  */
+
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __USB_CONF_H
+#define __USB_CONF_H
+
+/* Includes ------------------------------------------------------------------*/
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+
+/* These timings will be returned to the host when it checks the device
+   status during a write or erase operation to know how much time the host
+   should wait before issuing the next get status request. 
+   These defines are set in usb_conf.h file.
+   The values of this table should be extracted from relative memories 
+   datasheet (Typical or Maximum timming value for Sector Erase and for 
+   1024 bytes Write). All timings are expressed in millisecond unit (ms).
+   Note that "Sector" refers here to the memory unit used for Erase/Write 
+   operations. It could be a sector, a page, a block, a word ...
+   If the erase operation is not supported, it is advised to set the erase
+   timing to 1 (which means 1ms: one USB frame). */
+#define SPI_FLASH_SECTOR_ERASE_TIME     3000
+#define SPI_FLASH_SECTOR_WRITE_TIME     20
+
+#if defined(STM32L1XX_MD) || defined(STM32L1XX_HD)|| defined(STM32L1XX_MD_PLUS)    
+ #define INTERN_FLASH_SECTOR_ERASE_TIME 100
+ #define INTERN_FLASH_SECTOR_WRITE_TIME 104   
+#else
+ #define INTERN_FLASH_SECTOR_ERASE_TIME 50
+ #define INTERN_FLASH_SECTOR_WRITE_TIME 50
+#endif /* STM32L1XX_XD */   
+
+#define M29W128F_SECTOR_ERASE_TIME      1000
+#define M29W128F_SECTOR_WRITE_TIME      25 
+
+#define M29W128G_SECTOR_ERASE_TIME      1000
+#define M29W128G_SECTOR_WRITE_TIME      25
+
+#define S29GL128_SECTOR_ERASE_TIME      1000
+#define S29GL128_SECTOR_WRITE_TIME      45
+
+/* Exported macro ------------------------------------------------------------*/
+/* Exported functions ------------------------------------------------------- */
+/* External variables --------------------------------------------------------*/
+/*-------------------------------------------------------------*/
+/* EP_NUM */
+/* defines how many endpoints are used by the device */
+/*-------------------------------------------------------------*/
+#define EP_NUM                          (1)
+
+/*-------------------------------------------------------------*/
+/* --------------   Buffer Description Table  -----------------*/
+/*-------------------------------------------------------------*/
+/* buffer table base address */
+/* buffer table base address */
+#define BTABLE_ADDRESS      (0x00)
+
+/* EP0 */
+/* rx/tx buffer base address */
+#define ENDP0_RXADDR        (0x10)
+#define ENDP0_TXADDR        (0x50)
+
+
+/*-------------------------------------------------------------*/
+/* -------------------   ISTR events  -------------------------*/
+/*-------------------------------------------------------------*/
+/* IMR_MSK */
+/* mask defining which events has to be handled */
+/* by the device application software */
+#define IMR_MSK (CNTR_CTRM  | CNTR_WKUPM | CNTR_SUSPM | CNTR_ERRM  | CNTR_SOFM \
+                 | CNTR_ESOFM | CNTR_RESETM )
+
+/* CTR service routines */
+/* associated to defined endpoints */
+#define  EP1_IN_Callback   NOP_Process
+#define  EP2_IN_Callback   NOP_Process
+#define  EP3_IN_Callback   NOP_Process
+#define  EP4_IN_Callback   NOP_Process
+#define  EP5_IN_Callback   NOP_Process
+#define  EP6_IN_Callback   NOP_Process
+#define  EP7_IN_Callback   NOP_Process
+
+
+#define  EP1_OUT_Callback   NOP_Process
+#define  EP2_OUT_Callback   NOP_Process
+#define  EP3_OUT_Callback   NOP_Process
+#define  EP4_OUT_Callback   NOP_Process
+#define  EP5_OUT_Callback   NOP_Process
+#define  EP6_OUT_Callback   NOP_Process
+#define  EP7_OUT_Callback   NOP_Process
+
+#endif /*__USB_CONF_H*/
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
+