diff options
| -rw-r--r-- | .config | 14 | ||||
| -rw-r--r-- | .editorconfig | 3 | ||||
| -rw-r--r-- | .gdbinit | 2 | ||||
| -rw-r--r-- | .gitignore | 3 | ||||
| -rw-r--r-- | CMakeLists.txt | 27 | ||||
| -rw-r--r-- | Kconfig | 30 | ||||
| -rw-r--r-- | config.cmake | 5 | ||||
| -rw-r--r-- | openocd.cfg | 3 | ||||
| -rw-r--r-- | src/radio-controller.cpp | 25 | ||||
| -rw-r--r-- | stm32cubemx/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_uart.h | 751 | ||||
| -rw-r--r-- | stm32cubemx/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_uart.c | 1921 | ||||
| -rw-r--r-- | stm32cubemx/Inc/stm32f1xx_hal_conf.h | 2 | ||||
| -rw-r--r-- | stm32cubemx/Src/main.c | 38 | ||||
| -rw-r--r-- | stm32cubemx/Src/stm32f1xx_hal_msp.c | 64 | ||||
| -rw-r--r-- | stm32cubemx/Src/stm32f1xx_it.c | 14 | ||||
| -rw-r--r-- | stm32cubemx/stm32cubemx.gpdsc | 19 | ||||
| -rw-r--r-- | stm32cubemx/stm32cubemx.ioc | 41 |
17 files changed, 2919 insertions, 43 deletions
@@ -0,0 +1,14 @@ +# +# Automatically generated file; DO NOT EDIT. +# MCU C++ Configuration +# +CONFIG_TINYPRINTF=y +CONFIG_PRINTF_TARGET_SEMIHOSTING=y +# CONFIG_PRINTF_TARGET_UART is not set +CONFIG_SEMIHOSTING=y + +# +# Semihosting settings +# +CONFIG_SEMIHOSTING_PUTCHAR=y +CONFIG_SEMIHOSTING_PUTS=y diff --git a/.editorconfig b/.editorconfig index 4456701..8c27bca 100644 --- a/.editorconfig +++ b/.editorconfig @@ -9,3 +9,6 @@ indent_size = 4 [stm32cubemx/**.{h,c}] indent_size = 2 + +[*.cmake] +indent_size = 2 @@ -11,7 +11,7 @@ define target hookpost-extended-remote end define run_firmware - make -C build firmware + make -C build -j 4 firmware monitor reset halt @@ -1,3 +1,6 @@ build cmake-build-* .idea +.gdb_history + +.config.old diff --git a/CMakeLists.txt b/CMakeLists.txt index 2826974..002e4c4 100644 --- a/CMakeLists.txt +++ b/CMakeLists.txt @@ -7,6 +7,17 @@ project(radio-controller C CXX ASM) set(CMAKE_CXX_STANDARD 14) +include(config.cmake) + +add_custom_target(kconfig DEPENDS config.cmake) + +add_custom_command(OUTPUT .config config.cmake + COMMAND /home/trygvis/opt/kconfig/bin/kconfig-mconf Kconfig + COMMAND cat .config | thirdparty/mcucpp/config-to-cmake > config.cmake + COMMAND echo Generated config.cmake + WORKING_DIRECTORY ${CMAKE_CURRENT_SOURCE_DIR} + USES_TERMINAL) + add_executable(firmware src/radio-controller.cpp include/radio-controller.h) target_compile_definitions(firmware PUBLIC MCUCMAKE_USING_STM32CUBEMX=1) target_include_directories(firmware PUBLIC include) @@ -34,11 +45,25 @@ target_include_directories(firmware PUBLIC thirdparty/mcucpp/thirdparty/tinyprintf ) target_sources(firmware PUBLIC + thirdparty/mcucpp/include/mcu/arm/semihosting.h thirdparty/mcucpp/src/arm/semihosting.cpp - thirdparty/mcucpp/src/arm/semihosting-puts.cpp + thirdparty/mcucpp/src/arm/semihosting-puts.cpp thirdparty/mcucpp/src/arm/semihosting-putchar.cpp + thirdparty/mcucpp/src/generic/tinyprintf-printf.cpp thirdparty/mcucpp/src/generic/tinyprintf-snprintf.cpp + + thirdparty/mcucpp/include/mcu/nonew/function.h + thirdparty/mcucpp/include/mcu/nonew/queue.h + + thirdparty/mcucpp/include/mcu/io/output_stream.h + thirdparty/mcucpp/src/io/output_stream.cpp + + thirdparty/mcucpp/include/mcu/stm32cubemx/debug.h + + thirdparty/mcucpp/include/mcu/stm32cubemx/uart.h + thirdparty/mcucpp/src/stm32cubemx/uart.cpp + thirdparty/mcucpp/thirdparty/tinyprintf/tinyprintf.c ) @@ -0,0 +1,30 @@ +mainmenu "MCU C++ Configuration" + +config TINYPRINTF + bool "Enable tinyprintf" + +choice PRINTF_TARGET + prompt "printf() target" + + config PRINTF_TARGET_SEMIHOSTING + bool "Semihosting" + + config PRINTF_TARGET_UART + bool "UART" + +endchoice + +config SEMIHOSTING + bool "Enable semihosting" + +menu "Semihosting settings" + depends on SEMIHOSTING + +config SEMIHOSTING_PUTCHAR + bool "Enable putchar() implementation with semihosting" + default y + +config SEMIHOSTING_PUTS + bool "Enable puts() implementation with semihosting" + default y +endmenu diff --git a/config.cmake b/config.cmake new file mode 100644 index 0000000..94de0d7 --- /dev/null +++ b/config.cmake @@ -0,0 +1,5 @@ +set(KCONFIG_TINYPRINTF TRUE) +set(KCONFIG_PRINTF_TARGET_SEMIHOSTING TRUE) +set(KCONFIG_SEMIHOSTING TRUE) +set(KCONFIG_SEMIHOSTING_PUTCHAR TRUE) +set(KCONFIG_SEMIHOSTING_PUTS TRUE) diff --git a/openocd.cfg b/openocd.cfg index 48d7292..a3efc11 100644 --- a/openocd.cfg +++ b/openocd.cfg @@ -11,10 +11,11 @@ switch $device { "olimex-arm-usb-tiny-h" { source [find interface/ftdi/olimex-arm-usb-tiny-h.cfg] source [find interface/ftdi/olimex-arm-jtag-swd.cfg] - source [find target/stm32f1x.cfg] } } +source [find target/stm32f1x.cfg] + telnet_port disabled tcl_port disabled diff --git a/src/radio-controller.cpp b/src/radio-controller.cpp index c71aaa5..9795574 100644 --- a/src/radio-controller.cpp +++ b/src/radio-controller.cpp @@ -1,13 +1,18 @@ #include "radio-controller.h" #include "stm32f1xx_hal.h" -#include <cstring> #include "mcu/arm/semihosting.h" +#include "mcu/stm32cubemx/uart.h" +#include "mcu/stm32cubemx/debug.h" #ifdef HAL_IWDG_MODULE_ENABLED extern IWDG_HandleTypeDef hiwdg; #endif extern TIM_HandleTypeDef htim1; +extern UART_HandleTypeDef huart2; + +mcu::stm32cubemx::uart::uart_port uart2(&huart2); +mcu::stm32cubemx::debug::dbg<100> dbg(uart2); void main_pre_init() { } @@ -15,21 +20,33 @@ void main_pre_init() { void main_post_init() { semihosting::enable(); - HAL_TIM_Base_Start(&htim1); + printf("Radio Controller\n"); + + HAL_TIM_Base_Start_IT(&htim1); +// HAL_TIM_IC_Start_IT(&htim1, 1); + + uart2.enable(); } static uint32_t tick_next = 0; +static bool seen_high = false; + void main_loop() { -// printf("hello world!"); auto now = HAL_GetTick(); if (now >= tick_next) { +// puts(HAL_GPIO_ReadPin(GPIOA, GPIO_PIN_8) ? "1" : "0"); + uint32_t cnt = __HAL_TIM_GET_COUNTER(&htim1); - printf("cnt=%lu, now=%lu\n", cnt, now); + dbg.println("cnt=%lu, now=%lu, seen_high=%d", cnt, now, seen_high); tick_next += 1000; + seen_high = false; + dbg.println("wat"); } + seen_high |= HAL_GPIO_ReadPin(GPIOA, GPIO_PIN_8); + #ifdef HAL_IWDG_MODULE_ENABLED HAL_IWDG_Refresh(&hiwdg); #endif diff --git a/stm32cubemx/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_uart.h b/stm32cubemx/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_uart.h new file mode 100644 index 0000000..976756c --- /dev/null +++ b/stm32cubemx/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_uart.h @@ -0,0 +1,751 @@ +/** + ****************************************************************************** + * @file stm32f1xx_hal_uart.h + * @author MCD Application Team + * @version V1.0.4 + * @date 29-April-2016 + * @brief Header file of UART HAL module. + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT(c) 2016 STMicroelectronics</center></h2> + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F1xx_HAL_UART_H +#define __STM32F1xx_HAL_UART_H + +#ifdef __cplusplus + extern "C" { +#endif + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f1xx_hal_def.h" + +/** @addtogroup STM32F1xx_HAL_Driver + * @{ + */ + +/** @addtogroup UART + * @{ + */ + +/* Exported types ------------------------------------------------------------*/ +/** @defgroup UART_Exported_Types UART Exported Types + * @{ + */ + + +/** + * @brief UART Init Structure definition + */ +typedef struct +{ + uint32_t BaudRate; /*!< This member configures the UART communication baud rate. + The baud rate is computed using the following formula: + - IntegerDivider = ((PCLKx) / (16 * (huart->Init.BaudRate))) + - FractionalDivider = ((IntegerDivider - ((uint32_t) IntegerDivider)) * 16) + 0.5 */ + + uint32_t WordLength; /*!< Specifies the number of data bits transmitted or received in a frame. + This parameter can be a value of @ref UART_Word_Length */ + + uint32_t StopBits; /*!< Specifies the number of stop bits transmitted. + This parameter can be a value of @ref UART_Stop_Bits */ + + uint32_t Parity; /*!< Specifies the parity mode. + This parameter can be a value of @ref UART_Parity + @note When parity is enabled, the computed parity is inserted + at the MSB position of the transmitted data (9th bit when + the word length is set to 9 data bits; 8th bit when the + word length is set to 8 data bits). */ + + uint32_t Mode; /*!< Specifies wether the Receive or Transmit mode is enabled or disabled. + This parameter can be a value of @ref UART_Mode */ + + uint32_t HwFlowCtl; /*!< Specifies wether the hardware flow control mode is enabled + or disabled. + This parameter can be a value of @ref UART_Hardware_Flow_Control */ + + uint32_t OverSampling; /*!< Specifies whether the Over sampling 8 is enabled or disabled, to achieve higher speed (up to fPCLK/8). + This parameter can be a value of @ref UART_Over_Sampling. This feature is not available + on STM32F1xx family, so OverSampling parameter should always be set to 16. */ +}UART_InitTypeDef; + +/** + * @brief HAL UART State structures definition + */ +typedef enum +{ + HAL_UART_STATE_RESET = 0x00, /*!< Peripheral is not initialized */ + HAL_UART_STATE_READY = 0x01, /*!< Peripheral Initialized and ready for use */ + HAL_UART_STATE_BUSY = 0x02, /*!< an internal process is ongoing */ + HAL_UART_STATE_BUSY_TX = 0x12, /*!< Data Transmission process is ongoing */ + HAL_UART_STATE_BUSY_RX = 0x22, /*!< Data Reception process is ongoing */ + HAL_UART_STATE_BUSY_TX_RX = 0x32, /*!< Data Transmission and Reception process is ongoing */ + HAL_UART_STATE_TIMEOUT = 0x03, /*!< Timeout state */ + HAL_UART_STATE_ERROR = 0x04 /*!< Error */ +}HAL_UART_StateTypeDef; + + +/** + * @brief UART handle Structure definition + */ +typedef struct +{ + USART_TypeDef *Instance; /*!< UART registers base address */ + + UART_InitTypeDef Init; /*!< UART communication parameters */ + + uint8_t *pTxBuffPtr; /*!< Pointer to UART Tx transfer Buffer */ + + uint16_t TxXferSize; /*!< UART Tx Transfer size */ + + uint16_t TxXferCount; /*!< UART Tx Transfer Counter */ + + uint8_t *pRxBuffPtr; /*!< Pointer to UART Rx transfer Buffer */ + + uint16_t RxXferSize; /*!< UART Rx Transfer size */ + + uint16_t RxXferCount; /*!< UART Rx Transfer Counter */ + + DMA_HandleTypeDef *hdmatx; /*!< UART Tx DMA Handle parameters */ + + DMA_HandleTypeDef *hdmarx; /*!< UART Rx DMA Handle parameters */ + + HAL_LockTypeDef Lock; /*!< Locking object */ + + __IO HAL_UART_StateTypeDef State; /*!< UART communication state */ + + __IO uint32_t ErrorCode; /*!< UART Error code */ + +}UART_HandleTypeDef; + +/** + * @} + */ + +/* Exported constants --------------------------------------------------------*/ +/** @defgroup UART_Exported_Constants UART Exported constants + * @{ + */ + +/** @defgroup UART_Error_Codes UART Error Codes + * @{ + */ + +#define HAL_UART_ERROR_NONE ((uint32_t)0x00) /*!< No error */ +#define HAL_UART_ERROR_PE ((uint32_t)0x01) /*!< Parity error */ +#define HAL_UART_ERROR_NE ((uint32_t)0x02) /*!< Noise error */ +#define HAL_UART_ERROR_FE ((uint32_t)0x04) /*!< frame error */ +#define HAL_UART_ERROR_ORE ((uint32_t)0x08) /*!< Overrun error */ +#define HAL_UART_ERROR_DMA ((uint32_t)0x10) /*!< DMA transfer error */ + +/** + * @} + */ + + + + +/** @defgroup UART_Word_Length UART Word Length + * @{ + */ +#define UART_WORDLENGTH_8B ((uint32_t)0x00000000) +#define UART_WORDLENGTH_9B ((uint32_t)USART_CR1_M) +/** + * @} + */ + +/** @defgroup UART_Stop_Bits UART Number of Stop Bits + * @{ + */ +#define UART_STOPBITS_1 ((uint32_t)0x00000000) +#define UART_STOPBITS_2 ((uint32_t)USART_CR2_STOP_1) +/** + * @} + */ + +/** @defgroup UART_Parity UART Parity + * @{ + */ +#define UART_PARITY_NONE ((uint32_t)0x00000000) +#define UART_PARITY_EVEN ((uint32_t)USART_CR1_PCE) +#define UART_PARITY_ODD ((uint32_t)(USART_CR1_PCE | USART_CR1_PS)) +/** + * @} + */ + +/** @defgroup UART_Hardware_Flow_Control UART Hardware Flow Control + * @{ + */ +#define UART_HWCONTROL_NONE ((uint32_t)0x00000000) +#define UART_HWCONTROL_RTS ((uint32_t)USART_CR3_RTSE) +#define UART_HWCONTROL_CTS ((uint32_t)USART_CR3_CTSE) +#define UART_HWCONTROL_RTS_CTS ((uint32_t)(USART_CR3_RTSE | USART_CR3_CTSE)) +/** + * @} + */ + +/** @defgroup UART_Mode UART Transfer Mode + * @{ + */ +#define UART_MODE_RX ((uint32_t)USART_CR1_RE) +#define UART_MODE_TX ((uint32_t)USART_CR1_TE) +#define UART_MODE_TX_RX ((uint32_t)(USART_CR1_TE |USART_CR1_RE)) + +/** + * @} + */ + + /** @defgroup UART_State UART State + * @{ + */ +#define UART_STATE_DISABLE ((uint32_t)0x00000000) +#define UART_STATE_ENABLE ((uint32_t)USART_CR1_UE) +/** + * @} + */ + +/** @defgroup UART_Over_Sampling UART Over Sampling + * @{ + */ +#define UART_OVERSAMPLING_16 ((uint32_t)0x00000000) +/** + * @} + */ + +/** @defgroup UART_LIN_Break_Detection_Length UART LIN Break Detection Length + * @{ + */ +#define UART_LINBREAKDETECTLENGTH_10B ((uint32_t)0x00000000) +#define UART_LINBREAKDETECTLENGTH_11B ((uint32_t)USART_CR2_LBDL) +/** + * @} + */ + +/** @defgroup UART_WakeUp_functions UART Wakeup Functions + * @{ + */ +#define UART_WAKEUPMETHOD_IDLELINE ((uint32_t)0x00000000) +#define UART_WAKEUPMETHOD_ADDRESSMARK ((uint32_t)USART_CR1_WAKE) +/** + * @} + */ + +/** @defgroup UART_Flags UART FLags + * Elements values convention: 0xXXXX + * - 0xXXXX : Flag mask in the SR register + * @{ + */ +#define UART_FLAG_CTS ((uint32_t)USART_SR_CTS) +#define UART_FLAG_LBD ((uint32_t)USART_SR_LBD) +#define UART_FLAG_TXE ((uint32_t)USART_SR_TXE) +#define UART_FLAG_TC ((uint32_t)USART_SR_TC) +#define UART_FLAG_RXNE ((uint32_t)USART_SR_RXNE) +#define UART_FLAG_IDLE ((uint32_t)USART_SR_IDLE) +#define UART_FLAG_ORE ((uint32_t)USART_SR_ORE) +#define UART_FLAG_NE ((uint32_t)USART_SR_NE) +#define UART_FLAG_FE ((uint32_t)USART_SR_FE) +#define UART_FLAG_PE ((uint32_t)USART_SR_PE) +/** + * @} + */ + +/** @defgroup UART_Interrupt_definition UART Interrupt Definitions + * Elements values convention: 0xY000XXXX + * - XXXX : Interrupt mask (16 bits) in the Y register + * - Y : Interrupt source register (2bits) + * - 0001: CR1 register + * - 0010: CR2 register + * - 0011: CR3 register + * + * @{ + */ + +#define UART_IT_PE ((uint32_t)(UART_CR1_REG_INDEX << 28 | USART_CR1_PEIE)) +#define UART_IT_TXE ((uint32_t)(UART_CR1_REG_INDEX << 28 | USART_CR1_TXEIE)) +#define UART_IT_TC ((uint32_t)(UART_CR1_REG_INDEX << 28 | USART_CR1_TCIE)) +#define UART_IT_RXNE ((uint32_t)(UART_CR1_REG_INDEX << 28 | USART_CR1_RXNEIE)) +#define UART_IT_IDLE ((uint32_t)(UART_CR1_REG_INDEX << 28 | USART_CR1_IDLEIE)) + +#define UART_IT_LBD ((uint32_t)(UART_CR2_REG_INDEX << 28 | USART_CR2_LBDIE)) + +#define UART_IT_CTS ((uint32_t)(UART_CR3_REG_INDEX << 28 | USART_CR3_CTSIE)) +#define UART_IT_ERR ((uint32_t)(UART_CR3_REG_INDEX << 28 | USART_CR3_EIE)) + +/** + * @} + */ + +/** + * @} + */ + + +/* Exported macro ------------------------------------------------------------*/ +/** @defgroup UART_Exported_Macros UART Exported Macros + * @{ + */ + + +/** @brief Reset UART handle state + * @param __HANDLE__: specifies the UART Handle. + * UART Handle selects the USARTx or UARTy peripheral + * (USART,UART availability and x,y values depending on device). + * @retval None + */ +#define __HAL_UART_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_UART_STATE_RESET) + +/** @brief Flush the UART DR register + * @param __HANDLE__: specifies the UART Handle. + * UART Handle selects the USARTx or UARTy peripheral + * (USART,UART availability and x,y values depending on device). + */ +#define __HAL_UART_FLUSH_DRREGISTER(__HANDLE__) ((__HANDLE__)->Instance->DR) + +/** @brief Check whether the specified UART flag is set or not. + * @param __HANDLE__: specifies the UART Handle. + * UART Handle selects the USARTx or UARTy peripheral + * (USART,UART availability and x,y values depending on device). + * @param __FLAG__: specifies the flag to check. + * This parameter can be one of the following values: + * @arg UART_FLAG_CTS: CTS Change flag (not available for UART4 and UART5) + * @arg UART_FLAG_LBD: LIN Break detection flag + * @arg UART_FLAG_TXE: Transmit data register empty flag + * @arg UART_FLAG_TC: Transmission Complete flag + * @arg UART_FLAG_RXNE: Receive data register not empty flag + * @arg UART_FLAG_IDLE: Idle Line detection flag + * @arg UART_FLAG_ORE: OverRun Error flag + * @arg UART_FLAG_NE: Noise Error flag + * @arg UART_FLAG_FE: Framing Error flag + * @arg UART_FLAG_PE: Parity Error flag + * @retval The new state of __FLAG__ (TRUE or FALSE). + */ +#define __HAL_UART_GET_FLAG(__HANDLE__, __FLAG__) (((__HANDLE__)->Instance->SR & (__FLAG__)) == (__FLAG__)) + +/** @brief Clear the specified UART pending flag. + * @param __HANDLE__: specifies the UART Handle. + * UART Handle selects the USARTx or UARTy peripheral + * (USART,UART availability and x,y values depending on device). + * @param __FLAG__: specifies the flag to check. + * This parameter can be any combination of the following values: + * @arg UART_FLAG_CTS: CTS Change flag (not available for UART4 and UART5). + * @arg UART_FLAG_LBD: LIN Break detection flag. + * @arg UART_FLAG_TC: Transmission Complete flag. + * @arg UART_FLAG_RXNE: Receive data register not empty flag. + * + * @note PE (Parity error), FE (Framing error), NE (Noise error), ORE (OverRun + * error) and IDLE (Idle line detected) flags are cleared by software + * sequence: a read operation to USART_SR register followed by a read + * operation to USART_DR register. + * @note RXNE flag can be also cleared by a read to the USART_DR register. + * @note TC flag can be also cleared by software sequence: a read operation to + * USART_SR register followed by a write operation to USART_DR register. + * @note TXE flag is cleared only by a write to the USART_DR register. + * + * @retval None + */ +#define __HAL_UART_CLEAR_FLAG(__HANDLE__, __FLAG__) ((__HANDLE__)->Instance->SR = ~(__FLAG__)) + +/** @brief Clear the UART PE pending flag. + * @param __HANDLE__: specifies the UART Handle. + * UART Handle selects the USARTx or UARTy peripheral + * (USART,UART availability and x,y values depending on device). + * @retval None + */ +#define __HAL_UART_CLEAR_PEFLAG(__HANDLE__) \ +do{ \ + __IO uint32_t tmpreg; \ + tmpreg = (__HANDLE__)->Instance->SR; \ + tmpreg = (__HANDLE__)->Instance->DR; \ + UNUSED(tmpreg); \ +}while(0) + + + +/** @brief Clear the UART FE pending flag. + * @param __HANDLE__: specifies the UART Handle. + * UART Handle selects the USARTx or UARTy peripheral + * (USART,UART availability and x,y values depending on device). + * @retval None + */ +#define __HAL_UART_CLEAR_FEFLAG(__HANDLE__) __HAL_UART_CLEAR_PEFLAG(__HANDLE__) + +/** @brief Clear the UART NE pending flag. + * @param __HANDLE__: specifies the UART Handle. + * UART Handle selects the USARTx or UARTy peripheral + * (USART,UART availability and x,y values depending on device). + * @retval None + */ +#define __HAL_UART_CLEAR_NEFLAG(__HANDLE__) __HAL_UART_CLEAR_PEFLAG(__HANDLE__) + +/** @brief Clear the UART ORE pending flag. + * @param __HANDLE__: specifies the UART Handle. + * UART Handle selects the USARTx or UARTy peripheral + * (USART,UART availability and x,y values depending on device). + * @retval None + */ +#define __HAL_UART_CLEAR_OREFLAG(__HANDLE__) __HAL_UART_CLEAR_PEFLAG(__HANDLE__) + +/** @brief Clear the UART IDLE pending flag. + * @param __HANDLE__: specifies the UART Handle. + * UART Handle selects the USARTx or UARTy peripheral + * (USART,UART availability and x,y values depending on device). + * @retval None + */ +#define __HAL_UART_CLEAR_IDLEFLAG(__HANDLE__) __HAL_UART_CLEAR_PEFLAG(__HANDLE__) + +/** @brief Enable the specified UART interrupt. + * @param __HANDLE__: specifies the UART Handle. + * UART Handle selects the USARTx or UARTy peripheral + * (USART,UART availability and x,y values depending on device). + * @param __INTERRUPT__: specifies the UART interrupt source to enable. + * This parameter can be one of the following values: + * @arg UART_IT_CTS: CTS change interrupt + * @arg UART_IT_LBD: LIN Break detection interrupt + * @arg UART_IT_TXE: Transmit Data Register empty interrupt + * @arg UART_IT_TC: Transmission complete interrupt + * @arg UART_IT_RXNE: Receive Data register not empty interrupt + * @arg UART_IT_IDLE: Idle line detection interrupt + * @arg UART_IT_PE: Parity Error interrupt + * @arg UART_IT_ERR: Error interrupt(Frame error, noise error, overrun error) + * @retval None + */ +#define __HAL_UART_ENABLE_IT(__HANDLE__, __INTERRUPT__) ((((__INTERRUPT__) >> 28) == UART_CR1_REG_INDEX)? ((__HANDLE__)->Instance->CR1 |= ((__INTERRUPT__) & UART_IT_MASK)): \ + (((__INTERRUPT__) >> 28) == UART_CR2_REG_INDEX)? ((__HANDLE__)->Instance->CR2 |= ((__INTERRUPT__) & UART_IT_MASK)): \ + ((__HANDLE__)->Instance->CR3 |= ((__INTERRUPT__) & UART_IT_MASK))) + + +/** @brief Disable the specified UART interrupt. + * @param __HANDLE__: specifies the UART Handle. + * UART Handle selects the USARTx or UARTy peripheral + * (USART,UART availability and x,y values depending on device). + * @param __INTERRUPT__: specifies the UART interrupt source to disable. + * This parameter can be one of the following values: + * @arg UART_IT_CTS: CTS change interrupt + * @arg UART_IT_LBD: LIN Break detection interrupt + * @arg UART_IT_TXE: Transmit Data Register empty interrupt + * @arg UART_IT_TC: Transmission complete interrupt + * @arg UART_IT_RXNE: Receive Data register not empty interrupt + * @arg UART_IT_IDLE: Idle line detection interrupt + * @arg UART_IT_PE: Parity Error interrupt + * @arg UART_IT_ERR: Error interrupt(Frame error, noise error, overrun error) + * @retval None + */ +#define __HAL_UART_DISABLE_IT(__HANDLE__, __INTERRUPT__) ((((__INTERRUPT__) >> 28) == UART_CR1_REG_INDEX)? ((__HANDLE__)->Instance->CR1 &= ~((__INTERRUPT__) & UART_IT_MASK)): \ + (((__INTERRUPT__) >> 28) == UART_CR2_REG_INDEX)? ((__HANDLE__)->Instance->CR2 &= ~((__INTERRUPT__) & UART_IT_MASK)): \ + ((__HANDLE__)->Instance->CR3 &= ~ ((__INTERRUPT__) & UART_IT_MASK))) + +/** @brief Check whether the specified UART interrupt has occurred or not. + * @param __HANDLE__: specifies the UART Handle. + * UART Handle selects the USARTx or UARTy peripheral + * (USART,UART availability and x,y values depending on device). + * @param __IT__: specifies the UART interrupt source to check. + * This parameter can be one of the following values: + * @arg UART_IT_CTS: CTS change interrupt (not available for UART4 and UART5) + * @arg UART_IT_LBD: LIN Break detection interrupt + * @arg UART_IT_TXE: Transmit Data Register empty interrupt + * @arg UART_IT_TC: Transmission complete interrupt + * @arg UART_IT_RXNE: Receive Data register not empty interrupt + * @arg UART_IT_IDLE: Idle line detection interrupt + * @arg UART_IT_ERR: Error interrupt + * @retval The new state of __IT__ (TRUE or FALSE). + */ +#define __HAL_UART_GET_IT_SOURCE(__HANDLE__, __IT__) (((((__IT__) >> 28) == UART_CR1_REG_INDEX)? (__HANDLE__)->Instance->CR1:(((((uint32_t)(__IT__)) >> 28) == UART_CR2_REG_INDEX)? \ + (__HANDLE__)->Instance->CR2 : (__HANDLE__)->Instance->CR3)) & (((uint32_t)(__IT__)) & UART_IT_MASK)) + +/** @brief Enable CTS flow control + * This macro allows to enable CTS hardware flow control for a given UART instance, + * without need to call HAL_UART_Init() function. + * As involving direct access to UART registers, usage of this macro should be fully endorsed by user. + * @note As macro is expected to be used for modifying CTS Hw flow control feature activation, without need + * for USART instance Deinit/Init, following conditions for macro call should be fulfilled : + * - UART instance should have already been initialised (through call of HAL_UART_Init() ) + * - macro could only be called when corresponding UART instance is disabled (i.e __HAL_UART_DISABLE(__HANDLE__)) + * and should be followed by an Enable macro (i.e __HAL_UART_ENABLE(__HANDLE__)). + * @param __HANDLE__: specifies the UART Handle. + * This parameter can be any USARTx (supporting the HW Flow control feature). + * It is used to select the USART peripheral (USART availability and x value depending on device). + * @retval None + */ +#define __HAL_UART_HWCONTROL_CTS_ENABLE(__HANDLE__) \ + do{ \ + SET_BIT((__HANDLE__)->Instance->CR3, USART_CR3_CTSE); \ + (__HANDLE__)->Init.HwFlowCtl |= USART_CR3_CTSE; \ + } while(0) + +/** @brief Disable CTS flow control + * This macro allows to disable CTS hardware flow control for a given UART instance, + * without need to call HAL_UART_Init() function. + * As involving direct access to UART registers, usage of this macro should be fully endorsed by user. + * @note As macro is expected to be used for modifying CTS Hw flow control feature activation, without need + * for USART instance Deinit/Init, following conditions for macro call should be fulfilled : + * - UART instance should have already been initialised (through call of HAL_UART_Init() ) + * - macro could only be called when corresponding UART instance is disabled (i.e __HAL_UART_DISABLE(__HANDLE__)) + * and should be followed by an Enable macro (i.e __HAL_UART_ENABLE(__HANDLE__)). + * @param __HANDLE__: specifies the UART Handle. + * This parameter can be any USARTx (supporting the HW Flow control feature). + * It is used to select the USART peripheral (USART availability and x value depending on device). + * @retval None + */ +#define __HAL_UART_HWCONTROL_CTS_DISABLE(__HANDLE__) \ + do{ \ + CLEAR_BIT((__HANDLE__)->Instance->CR3, USART_CR3_CTSE); \ + (__HANDLE__)->Init.HwFlowCtl &= ~(USART_CR3_CTSE); \ + } while(0) + +/** @brief Enable RTS flow control + * This macro allows to enable RTS hardware flow control for a given UART instance, + * without need to call HAL_UART_Init() function. + * As involving direct access to UART registers, usage of this macro should be fully endorsed by user. + * @note As macro is expected to be used for modifying RTS Hw flow control feature activation, without need + * for USART instance Deinit/Init, following conditions for macro call should be fulfilled : + * - UART instance should have already been initialised (through call of HAL_UART_Init() ) + * - macro could only be called when corresponding UART instance is disabled (i.e __HAL_UART_DISABLE(__HANDLE__)) + * and should be followed by an Enable macro (i.e __HAL_UART_ENABLE(__HANDLE__)). + * @param __HANDLE__: specifies the UART Handle. + * This parameter can be any USARTx (supporting the HW Flow control feature). + * It is used to select the USART peripheral (USART availability and x value depending on device). + * @retval None + */ +#define __HAL_UART_HWCONTROL_RTS_ENABLE(__HANDLE__) \ + do{ \ + SET_BIT((__HANDLE__)->Instance->CR3, USART_CR3_RTSE); \ + (__HANDLE__)->Init.HwFlowCtl |= USART_CR3_RTSE; \ + } while(0) + +/** @brief Disable RTS flow control + * This macro allows to disable RTS hardware flow control for a given UART instance, + * without need to call HAL_UART_Init() function. + * As involving direct access to UART registers, usage of this macro should be fully endorsed by user. + * @note As macro is expected to be used for modifying RTS Hw flow control feature activation, without need + * for USART instance Deinit/Init, following conditions for macro call should be fulfilled : + * - UART instance should have already been initialised (through call of HAL_UART_Init() ) + * - macro could only be called when corresponding UART instance is disabled (i.e __HAL_UART_DISABLE(__HANDLE__)) + * and should be followed by an Enable macro (i.e __HAL_UART_ENABLE(__HANDLE__)). + * @param __HANDLE__: specifies the UART Handle. + * This parameter can be any USARTx (supporting the HW Flow control feature). + * It is used to select the USART peripheral (USART availability and x value depending on device). + * @retval None + */ +#define __HAL_UART_HWCONTROL_RTS_DISABLE(__HANDLE__) \ + do{ \ + CLEAR_BIT((__HANDLE__)->Instance->CR3, USART_CR3_RTSE);\ + (__HANDLE__)->Init.HwFlowCtl &= ~(USART_CR3_RTSE); \ + } while(0) + + +/** @brief Enable UART + * @param __HANDLE__: specifies the UART Handle. + * UART Handle selects the USARTx or UARTy peripheral + * (USART,UART availability and x,y values depending on device). + * @retval None + */ +#define __HAL_UART_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->CR1 |= USART_CR1_UE) + +/** @brief Disable UART + * UART Handle selects the USARTx or UARTy peripheral + * (USART,UART availability and x,y values depending on device). + * @retval None + */ +#define __HAL_UART_DISABLE(__HANDLE__) ((__HANDLE__)->Instance->CR1 &= ~USART_CR1_UE) + +/** + * @} + */ + + +/* Private macros --------------------------------------------------------*/ +/** @defgroup UART_Private_Macros UART Private Macros + * @{ + */ + +#define UART_CR1_REG_INDEX 1 +#define UART_CR2_REG_INDEX 2 +#define UART_CR3_REG_INDEX 3 + +#define UART_DIV_SAMPLING16(_PCLK_, _BAUD_) (((_PCLK_)*25)/(4*(_BAUD_))) +#define UART_DIVMANT_SAMPLING16(_PCLK_, _BAUD_) (UART_DIV_SAMPLING16((_PCLK_), (_BAUD_))/100) +#define UART_DIVFRAQ_SAMPLING16(_PCLK_, _BAUD_) (((UART_DIV_SAMPLING16((_PCLK_), (_BAUD_)) - (UART_DIVMANT_SAMPLING16((_PCLK_), (_BAUD_)) * 100)) * 16 + 50) / 100) +/* UART BRR = mantissa + overflow + fraction + = (UART DIVMANT << 4) + (UART DIVFRAQ & 0xF0) + (UART DIVFRAQ & 0x0F) */ +#define UART_BRR_SAMPLING16(_PCLK_, _BAUD_) (((UART_DIVMANT_SAMPLING16((_PCLK_), (_BAUD_)) << 4) + \ + (UART_DIVFRAQ_SAMPLING16((_PCLK_), (_BAUD_)) & 0xF0)) + \ + (UART_DIVFRAQ_SAMPLING16((_PCLK_), (_BAUD_)) & 0x0F)) +#define IS_UART_WORD_LENGTH(LENGTH) (((LENGTH) == UART_WORDLENGTH_8B) || \ + ((LENGTH) == UART_WORDLENGTH_9B)) +#define IS_UART_LIN_WORD_LENGTH(LENGTH) ((LENGTH) == UART_WORDLENGTH_8B) + +#define IS_UART_STOPBITS(STOPBITS) (((STOPBITS) == UART_STOPBITS_1) || \ + ((STOPBITS) == UART_STOPBITS_2)) + +#define IS_UART_PARITY(PARITY) (((PARITY) == UART_PARITY_NONE) || \ + ((PARITY) == UART_PARITY_EVEN) || \ + ((PARITY) == UART_PARITY_ODD)) + +#define IS_UART_HARDWARE_FLOW_CONTROL(CONTROL)\ + (((CONTROL) == UART_HWCONTROL_NONE) || \ + ((CONTROL) == UART_HWCONTROL_RTS) || \ + ((CONTROL) == UART_HWCONTROL_CTS) || \ + ((CONTROL) == UART_HWCONTROL_RTS_CTS)) + +#define IS_UART_MODE(MODE) ((((MODE) & (~((uint32_t)UART_MODE_TX_RX))) == 0x00) && \ + ((MODE) != (uint32_t)0x00000000)) + +#define IS_UART_STATE(STATE) (((STATE) == UART_STATE_DISABLE) || \ + ((STATE) == UART_STATE_ENABLE)) + +#define IS_UART_OVERSAMPLING(SAMPLING) ((SAMPLING) == UART_OVERSAMPLING_16) +#define IS_UART_LIN_OVERSAMPLING(SAMPLING) ((SAMPLING) == UART_OVERSAMPLING_16) + +#define IS_UART_LIN_BREAK_DETECT_LENGTH(LENGTH) (((LENGTH) == UART_LINBREAKDETECTLENGTH_10B) || \ + ((LENGTH) == UART_LINBREAKDETECTLENGTH_11B)) + +#define IS_UART_WAKEUPMETHOD(WAKEUP) (((WAKEUP) == UART_WAKEUPMETHOD_IDLELINE) || \ + ((WAKEUP) == UART_WAKEUPMETHOD_ADDRESSMARK)) + + +/** Check UART Baud rate + * __BAUDRATE__: Baudrate specified by the user + * The maximum Baud Rate is derived from the maximum clock on APB (i.e. 72 MHz) + * divided by the smallest oversampling used on the USART (i.e. 16) + * Retrun : TRUE or FALSE + */ +#define IS_UART_BAUDRATE(__BAUDRATE__) ((__BAUDRATE__) < 4500001) + +/** Check UART Node Address + * __ADDRESS__: UART Node address specified by the user + * UART Node address is used in Multi processor communication for wakeup + * with address mark detection. + * This parameter must be a number between Min_Data = 0 and Max_Data = 15 + * Return : TRUE or FALSE + */ +#define IS_UART_ADDRESS(__ADDRESS__) ((__ADDRESS__) <= 0xF) + +/** UART interruptions flag mask + */ +#define UART_IT_MASK ((uint32_t) USART_CR1_PEIE | USART_CR1_TXEIE | USART_CR1_TCIE | USART_CR1_RXNEIE | \ + USART_CR1_IDLEIE | USART_CR2_LBDIE | USART_CR3_CTSIE | USART_CR3_EIE ) + +/** + * @} + */ + +/* Exported functions --------------------------------------------------------*/ + +/** @addtogroup UART_Exported_Functions UART Exported Functions + * @{ + */ + +/** @addtogroup UART_Exported_Functions_Group1 Initialization and de-initialization functions + * @{ + */ + +/* Initialization and de-initialization functions ****************************/ +HAL_StatusTypeDef HAL_UART_Init(UART_HandleTypeDef *huart); +HAL_StatusTypeDef HAL_HalfDuplex_Init(UART_HandleTypeDef *huart); +HAL_StatusTypeDef HAL_LIN_Init(UART_HandleTypeDef *huart, uint32_t BreakDetectLength); +HAL_StatusTypeDef HAL_MultiProcessor_Init(UART_HandleTypeDef *huart, uint8_t Address, uint32_t WakeUpMethod); +HAL_StatusTypeDef HAL_UART_DeInit (UART_HandleTypeDef *huart); +void HAL_UART_MspInit(UART_HandleTypeDef *huart); +void HAL_UART_MspDeInit(UART_HandleTypeDef *huart); + +/** + * @} + */ + +/** @addtogroup UART_Exported_Functions_Group2 IO operation functions + * @{ + */ + +/* IO operation functions *****************************************************/ +HAL_StatusTypeDef HAL_UART_Transmit(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size, uint32_t Timeout); +HAL_StatusTypeDef HAL_UART_Receive(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size, uint32_t Timeout); +HAL_StatusTypeDef HAL_UART_Transmit_IT(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size); +HAL_StatusTypeDef HAL_UART_Receive_IT(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size); +HAL_StatusTypeDef HAL_UART_Transmit_DMA(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size); +HAL_StatusTypeDef HAL_UART_Receive_DMA(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size); +HAL_StatusTypeDef HAL_UART_DMAPause(UART_HandleTypeDef *huart); +HAL_StatusTypeDef HAL_UART_DMAResume(UART_HandleTypeDef *huart); +HAL_StatusTypeDef HAL_UART_DMAStop(UART_HandleTypeDef *huart); +void HAL_UART_IRQHandler(UART_HandleTypeDef *huart); +void HAL_UART_TxCpltCallback(UART_HandleTypeDef *huart); +void HAL_UART_TxHalfCpltCallback(UART_HandleTypeDef *huart); +void HAL_UART_RxCpltCallback(UART_HandleTypeDef *huart); +void HAL_UART_RxHalfCpltCallback(UART_HandleTypeDef *huart); +void HAL_UART_ErrorCallback(UART_HandleTypeDef *huart); + +/** + * @} + */ + +/** @addtogroup UART_Exported_Functions_Group3 Peripheral Control functions + * @{ + */ + +/* Peripheral Control functions ************************************************/ +HAL_StatusTypeDef HAL_LIN_SendBreak(UART_HandleTypeDef *huart); +HAL_StatusTypeDef HAL_MultiProcessor_EnterMuteMode(UART_HandleTypeDef *huart); +HAL_StatusTypeDef HAL_MultiProcessor_ExitMuteMode(UART_HandleTypeDef *huart); +HAL_StatusTypeDef HAL_HalfDuplex_EnableTransmitter(UART_HandleTypeDef *huart); +HAL_StatusTypeDef HAL_HalfDuplex_EnableReceiver(UART_HandleTypeDef *huart); + +/** + * @} + */ + +/** @addtogroup UART_Exported_Functions_Group4 Peripheral State and Errors functions + * @{ + */ + +/* Peripheral State and Errors functions **************************************************/ +HAL_UART_StateTypeDef HAL_UART_GetState(UART_HandleTypeDef *huart); +uint32_t HAL_UART_GetError(UART_HandleTypeDef *huart); + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32F1xx_HAL_UART_H */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/stm32cubemx/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_uart.c b/stm32cubemx/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_uart.c new file mode 100644 index 0000000..8f06df7 --- /dev/null +++ b/stm32cubemx/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_uart.c @@ -0,0 +1,1921 @@ +/** + ****************************************************************************** + * @file stm32f1xx_hal_uart.c + * @author MCD Application Team + * @version V1.0.4 + * @date 29-April-2016 + * @brief UART HAL module driver. + * This file provides firmware functions to manage the following + * functionalities of the Universal Asynchronous Receiver Transmitter (UART) peripheral: + * + Initialization and de-initialization functions + * + IO operation functions + * + Peripheral Control functions + * + Peripheral State and Errors functions + @verbatim + ============================================================================== + ##### How to use this driver ##### + ============================================================================== + [..] + The UART HAL driver can be used as follows: + + (#) Declare a UART_HandleTypeDef handle structure. + + (#) Initialize the UART low level resources by implementing the HAL_UART_MspInit() API: + (##) Enable the USARTx interface clock. + (##) UART pins configuration: + (+++) Enable the clock for the UART GPIOs. + (+++) Configure the USART pins (TX as alternate function pull-up, RX as alternate function Input). + (##) NVIC configuration if you need to use interrupt process (HAL_UART_Transmit_IT() + and HAL_UART_Receive_IT() APIs): + (+++) Configure the USARTx interrupt priority. + (+++) Enable the NVIC USART IRQ handle. + (##) DMA Configuration if you need to use DMA process (HAL_UART_Transmit_DMA() + and HAL_UART_Receive_DMA() APIs): + (+++) Declare a DMA handle structure for the Tx/Rx channel. + (+++) Enable the DMAx interface clock. + (+++) Configure the declared DMA handle structure with the required + Tx/Rx parameters. + (+++) Configure the DMA Tx/Rx channel. + (+++) Associate the initialized DMA handle to the UART DMA Tx/Rx handle. + (+++) Configure the priority and enable the NVIC for the transfer complete + interrupt on the DMA Tx/Rx channel. + (+++) Configure the USARTx interrupt priority and enable the NVIC USART IRQ handle + (used for last byte sending completion detection in DMA non circular mode) + + (#) Program the Baud Rate, Word Length, Stop Bit, Parity, Hardware + flow control and Mode(Receiver/Transmitter) in the huart Init structure. + + (#) For the UART asynchronous mode, initialize the UART registers by calling + the HAL_UART_Init() API. + + (#) For the UART Half duplex mode, initialize the UART registers by calling + the HAL_HalfDuplex_Init() API. + + (#) For the LIN mode, initialize the UART registers by calling the HAL_LIN_Init() API. + + (#) For the Multi-Processor mode, initialize the UART registers by calling + the HAL_MultiProcessor_Init() API. + + [..] + (@) The specific UART interrupts (Transmission complete interrupt, + RXNE interrupt and Error Interrupts) will be managed using the macros + __HAL_UART_ENABLE_IT() and __HAL_UART_DISABLE_IT() inside the transmit + and receive process. + + [..] + (@) These APIs (HAL_UART_Init() and HAL_HalfDuplex_Init()) configure also the + low level Hardware GPIO, CLOCK, CORTEX...etc) by calling the customed + HAL_UART_MspInit() API. + + [..] + Three operation modes are available within this driver : + + *** Polling mode IO operation *** + ================================= + [..] + (+) Send an amount of data in blocking mode using HAL_UART_Transmit() + (+) Receive an amount of data in blocking mode using HAL_UART_Receive() + + *** Interrupt mode IO operation *** + =================================== + [..] + (+) Send an amount of data in non blocking mode using HAL_UART_Transmit_IT() + (+) At transmission end of transfer HAL_UART_TxCpltCallback is executed and user can + add his own code by customization of function pointer HAL_UART_TxCpltCallback + (+) Receive an amount of data in non blocking mode using HAL_UART_Receive_IT() + (+) At reception end of transfer HAL_UART_RxCpltCallback is executed and user can + add his own code by customization of function pointer HAL_UART_RxCpltCallback + (+) In case of transfer Error, HAL_UART_ErrorCallback() function is executed and user can + add his own code by customization of function pointer HAL_UART_ErrorCallback + + *** DMA mode IO operation *** + ============================== + [..] + (+) Send an amount of data in non blocking mode (DMA) using HAL_UART_Transmit_DMA() + (+) At transmission end of half transfer HAL_UART_TxHalfCpltCallback is executed and user can + add his own code by customization of function pointer HAL_UART_TxHalfCpltCallback + (+) At transmission end of transfer HAL_UART_TxCpltCallback is executed and user can + add his own code by customization of function pointer HAL_UART_TxCpltCallback + (+) Receive an amount of data in non blocking mode (DMA) using HAL_UART_Receive_DMA() + (+) At reception end of half transfer HAL_UART_RxHalfCpltCallback is executed and user can + add his own code by customization of function pointer HAL_UART_RxHalfCpltCallback + (+) At reception end of transfer HAL_UART_RxCpltCallback is executed and user can + add his own code by customization of function pointer HAL_UART_RxCpltCallback + (+) In case of transfer Error, HAL_UART_ErrorCallback() function is executed and user can + add his own code by customization of function pointer HAL_UART_ErrorCallback + (+) Pause the DMA Transfer using HAL_UART_DMAPause() + (+) Resume the DMA Transfer using HAL_UART_DMAResume() + (+) Stop the DMA Transfer using HAL_UART_DMAStop() + + *** UART HAL driver macros list *** + ============================================= + [..] + Below the list of most used macros in UART HAL driver. + + (+) __HAL_UART_ENABLE: Enable the UART peripheral + (+) __HAL_UART_DISABLE: Disable the UART peripheral + (+) __HAL_UART_GET_FLAG : Check whether the specified UART flag is set or not + (+) __HAL_UART_CLEAR_FLAG : Clear the specified UART pending flag + (+) __HAL_UART_ENABLE_IT: Enable the specified UART interrupt + (+) __HAL_UART_DISABLE_IT: Disable the specified UART interrupt + (+) __HAL_UART_GET_IT_SOURCE: Check whether the specified UART interrupt has occurred or not + + [..] + (@) You can refer to the UART HAL driver header file for more useful macros + + @endverbatim + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT(c) 2016 STMicroelectronics</center></h2> + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f1xx_hal.h" + +/** @addtogroup STM32F1xx_HAL_Driver + * @{ + */ + +/** @defgroup UART UART + * @brief HAL UART module driver + * @{ + */ +#ifdef HAL_UART_MODULE_ENABLED + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +/* Private macros ------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ +/** @addtogroup UART_Private_Functions UART Private Functions + * @{ + */ +static void UART_SetConfig (UART_HandleTypeDef *huart); +static HAL_StatusTypeDef UART_Transmit_IT(UART_HandleTypeDef *huart); +static HAL_StatusTypeDef UART_EndTransmit_IT(UART_HandleTypeDef *huart); +static HAL_StatusTypeDef UART_Receive_IT(UART_HandleTypeDef *huart); +static void UART_DMATransmitCplt(DMA_HandleTypeDef *hdma); +static void UART_DMATxHalfCplt(DMA_HandleTypeDef *hdma); +static void UART_DMAReceiveCplt(DMA_HandleTypeDef *hdma); +static void UART_DMARxHalfCplt(DMA_HandleTypeDef *hdma); +static void UART_DMAError(DMA_HandleTypeDef *hdma); +static HAL_StatusTypeDef UART_WaitOnFlagUntilTimeout(UART_HandleTypeDef *huart, uint32_t Flag, FlagStatus Status, uint32_t Timeout); +/** + * @} + */ + +/* Exported functions ---------------------------------------------------------*/ + +/** @defgroup UART_Exported_Functions UART Exported Functions + * @{ + */ + +/** @defgroup UART_Exported_Functions_Group1 Initialization and de-initialization functions + * @brief Initialization and Configuration functions + * +@verbatim +=============================================================================== + ##### Initialization and Configuration functions ##### + =============================================================================== + [..] + This subsection provides a set of functions allowing to initialize the USARTx or the UARTy + in asynchronous mode. + (+) For the asynchronous mode only these parameters can be configured: + (++) Baud Rate + (++) Word Length + (++) Stop Bit + (++) Parity + (++) Hardware flow control + (++) Receiver/transmitter modes + [..] + The HAL_UART_Init(), HAL_HalfDuplex_Init(), HAL_LIN_Init() and HAL_MultiProcessor_Init() APIs + follow respectively the UART asynchronous, UART Half duplex, LIN and Multi-Processor + configuration procedures (details for the procedures are available in reference manuals + (RM0008 for STM32F10Xxx MCUs and RM0041 for STM32F100xx MCUs)). + + +@endverbatim + * @{ + */ + +/* + Additionnal remark: If the parity is enabled, then the MSB bit of the data written + in the data register is transmitted but is changed by the parity bit. + Depending on the frame length defined by the M bit (8-bits or 9-bits), + the possible UART frame formats are as listed in the following table: + +-------------------------------------------------------------+ + | M bit | PCE bit | UART frame | + |---------------------|---------------------------------------| + | 0 | 0 | | SB | 8 bit data | STB | | + |---------|-----------|---------------------------------------| + | 0 | 1 | | SB | 7 bit data | PB | STB | | + |---------|-----------|---------------------------------------| + | 1 | 0 | | SB | 9 bit data | STB | | + |---------|-----------|---------------------------------------| + | 1 | 1 | | SB | 8 bit data | PB | STB | | + +-------------------------------------------------------------+ +*/ + +/** + * @brief Initializes the UART mode according to the specified parameters in + * the UART_InitTypeDef and create the associated handle. + * @param huart: Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_Init(UART_HandleTypeDef *huart) +{ + /* Check the UART handle allocation */ + if(huart == NULL) + { + return HAL_ERROR; + } + + /* Check the parameters */ + if(huart->Init.HwFlowCtl != UART_HWCONTROL_NONE) + { + /* The hardware flow control is available only for USART1, USART2, USART3 */ + assert_param(IS_UART_HWFLOW_INSTANCE(huart->Instance)); + assert_param(IS_UART_HARDWARE_FLOW_CONTROL(huart->Init.HwFlowCtl)); + } + else + { + assert_param(IS_UART_INSTANCE(huart->Instance)); + } + assert_param(IS_UART_WORD_LENGTH(huart->Init.WordLength)); + assert_param(IS_UART_OVERSAMPLING(huart->Init.OverSampling)); + + if(huart->State == HAL_UART_STATE_RESET) + { + /* Allocate lock resource and initialize it */ + huart->Lock = HAL_UNLOCKED; + + /* Init the low level hardware */ + HAL_UART_MspInit(huart); + } + + huart->State = HAL_UART_STATE_BUSY; + + /* Disable the peripheral */ + __HAL_UART_DISABLE(huart); + + /* Set the UART Communication parameters */ + UART_SetConfig(huart); + + /* In asynchronous mode, the following bits must be kept cleared: + - LINEN and CLKEN bits in the USART_CR2 register, + - SCEN, HDSEL and IREN bits in the USART_CR3 register.*/ + CLEAR_BIT(huart->Instance->CR2, (USART_CR2_LINEN | USART_CR2_CLKEN)); + CLEAR_BIT(huart->Instance->CR3, (USART_CR3_SCEN | USART_CR3_HDSEL | USART_CR3_IREN)); + + /* Enable the peripheral */ + __HAL_UART_ENABLE(huart); + + /* Initialize the UART state */ + huart->ErrorCode = HAL_UART_ERROR_NONE; + huart->State= HAL_UART_STATE_READY; + + return HAL_OK; +} + +/** + * @brief Initializes the half-duplex mode according to the specified + * parameters in the UART_InitTypeDef and create the associated handle. + * @param huart: Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_HalfDuplex_Init(UART_HandleTypeDef *huart) +{ + /* Check the UART handle allocation */ + if(huart == NULL) + { + return HAL_ERROR; + } + + /* Check UART instance */ + assert_param(IS_UART_HALFDUPLEX_INSTANCE(huart->Instance)); + assert_param(IS_UART_WORD_LENGTH(huart->Init.WordLength)); + assert_param(IS_UART_OVERSAMPLING(huart->Init.OverSampling)); + + if(huart->State == HAL_UART_STATE_RESET) + { + /* Allocate lock resource and initialize it */ + huart->Lock = HAL_UNLOCKED; + + /* Init the low level hardware */ + HAL_UART_MspInit(huart); + } + + huart->State = HAL_UART_STATE_BUSY; + + /* Disable the peripheral */ + __HAL_UART_DISABLE(huart); + + /* Set the UART Communication parameters */ + UART_SetConfig(huart); + + /* In half-duplex mode, the following bits must be kept cleared: + - LINEN and CLKEN bits in the USART_CR2 register, + - SCEN and IREN bits in the USART_CR3 register.*/ + CLEAR_BIT(huart->Instance->CR2, (USART_CR2_LINEN | USART_CR2_CLKEN)); + CLEAR_BIT(huart->Instance->CR3, (USART_CR3_IREN | USART_CR3_SCEN)); + + /* Enable the Half-Duplex mode by setting the HDSEL bit in the CR3 register */ + SET_BIT(huart->Instance->CR3, USART_CR3_HDSEL); + + /* Enable the peripheral */ + __HAL_UART_ENABLE(huart); + + /* Initialize the UART state*/ + huart->ErrorCode = HAL_UART_ERROR_NONE; + huart->State= HAL_UART_STATE_READY; + + return HAL_OK; +} + +/** + * @brief Initializes the LIN mode according to the specified + * parameters in the UART_InitTypeDef and create the associated handle. + * @param huart: Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @param BreakDetectLength: Specifies the LIN break detection length. + * This parameter can be one of the following values: + * @arg UART_LINBREAKDETECTLENGTH_10B: 10-bit break detection + * @arg UART_LINBREAKDETECTLENGTH_11B: 11-bit break detection + * @retval HAL status + */ +HAL_StatusTypeDef HAL_LIN_Init(UART_HandleTypeDef *huart, uint32_t BreakDetectLength) +{ + /* Check the UART handle allocation */ + if(huart == NULL) + { + return HAL_ERROR; + } + + /* Check the LIN UART instance */ + assert_param(IS_UART_LIN_INSTANCE(huart->Instance)); + /* Check the Break detection length parameter */ + assert_param(IS_UART_LIN_BREAK_DETECT_LENGTH(BreakDetectLength)); + assert_param(IS_UART_LIN_WORD_LENGTH(huart->Init.WordLength)); + assert_param(IS_UART_LIN_OVERSAMPLING(huart->Init.OverSampling)); + + if(huart->State == HAL_UART_STATE_RESET) + { + /* Allocate lock resource and initialize it */ + huart->Lock = HAL_UNLOCKED; + + /* Init the low level hardware */ + HAL_UART_MspInit(huart); + } + + huart->State = HAL_UART_STATE_BUSY; + + /* Disable the peripheral */ + __HAL_UART_DISABLE(huart); + + /* Set the UART Communication parameters */ + UART_SetConfig(huart); + + /* In LIN mode, the following bits must be kept cleared: + - CLKEN bits in the USART_CR2 register, + - SCEN and IREN bits in the USART_CR3 register.*/ + CLEAR_BIT(huart->Instance->CR2, USART_CR2_CLKEN); + CLEAR_BIT(huart->Instance->CR3, (USART_CR3_HDSEL | USART_CR3_IREN | USART_CR3_SCEN)); + + /* Enable the LIN mode by setting the LINEN bit in the CR2 register */ + SET_BIT(huart->Instance->CR2, USART_CR2_LINEN); + + /* Set the USART LIN Break detection length. */ + MODIFY_REG(huart->Instance->CR2, USART_CR2_LBDL, BreakDetectLength); + + /* Enable the peripheral */ + __HAL_UART_ENABLE(huart); + + /* Initialize the UART state*/ + huart->ErrorCode = HAL_UART_ERROR_NONE; + huart->State= HAL_UART_STATE_READY; + + return HAL_OK; +} + +/** + * @brief Initializes the Multi-Processor mode according to the specified + * parameters in the UART_InitTypeDef and create the associated handle. + * @param huart: Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @param Address: UART node address + * @param WakeUpMethod: specifies the UART wakeup method. + * This parameter can be one of the following values: + * @arg UART_WAKEUPMETHOD_IDLELINE: Wakeup by an idle line detection + * @arg UART_WAKEUPMETHOD_ADDRESSMARK: Wakeup by an address mark + * @retval HAL status + */ +HAL_StatusTypeDef HAL_MultiProcessor_Init(UART_HandleTypeDef *huart, uint8_t Address, uint32_t WakeUpMethod) +{ + /* Check the UART handle allocation */ + if(huart == NULL) + { + return HAL_ERROR; + } + + /* Check UART instance capabilities */ + assert_param(IS_UART_MULTIPROCESSOR_INSTANCE(huart->Instance)); + + /* Check the Address & wake up method parameters */ + assert_param(IS_UART_WAKEUPMETHOD(WakeUpMethod)); + assert_param(IS_UART_ADDRESS(Address)); + assert_param(IS_UART_WORD_LENGTH(huart->Init.WordLength)); + assert_param(IS_UART_OVERSAMPLING(huart->Init.OverSampling)); + + if(huart->State == HAL_UART_STATE_RESET) + { + /* Allocate lock resource and initialize it */ + huart->Lock = HAL_UNLOCKED; + + /* Init the low level hardware */ + HAL_UART_MspInit(huart); + } + + huart->State = HAL_UART_STATE_BUSY; + + /* Disable the peripheral */ + __HAL_UART_DISABLE(huart); + + /* Set the UART Communication parameters */ + UART_SetConfig(huart); + + /* In Multi-Processor mode, the following bits must be kept cleared: + - LINEN and CLKEN bits in the USART_CR2 register, + - SCEN, HDSEL and IREN bits in the USART_CR3 register */ + CLEAR_BIT(huart->Instance->CR2, (USART_CR2_LINEN | USART_CR2_CLKEN)); + CLEAR_BIT(huart->Instance->CR3, (USART_CR3_SCEN | USART_CR3_HDSEL | USART_CR3_IREN)); + + /* Set the USART address node */ + MODIFY_REG(huart->Instance->CR2, USART_CR2_ADD, Address); + + /* Set the wake up method by setting the WAKE bit in the CR1 register */ + MODIFY_REG(huart->Instance->CR1, USART_CR1_WAKE, WakeUpMethod); + + /* Enable the peripheral */ + __HAL_UART_ENABLE(huart); + + /* Initialize the UART state */ + huart->ErrorCode = HAL_UART_ERROR_NONE; + huart->State= HAL_UART_STATE_READY; + + return HAL_OK; +} + +/** + * @brief DeInitializes the UART peripheral. + * @param huart: Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_DeInit(UART_HandleTypeDef *huart) +{ + /* Check the UART handle allocation */ + if(huart == NULL) + { + return HAL_ERROR; + } + + /* Check the parameters */ + assert_param(IS_UART_INSTANCE(huart->Instance)); + + huart->State = HAL_UART_STATE_BUSY; + + /* Disable the Peripheral */ + __HAL_UART_DISABLE(huart); + + huart->Instance->CR1 = 0x0; + huart->Instance->CR2 = 0x0; + huart->Instance->CR3 = 0x0; + + /* DeInit the low level hardware */ + HAL_UART_MspDeInit(huart); + + huart->ErrorCode = HAL_UART_ERROR_NONE; + huart->State = HAL_UART_STATE_RESET; + + /* Process Unlock */ + __HAL_UNLOCK(huart); + + return HAL_OK; +} + +/** + * @brief UART MSP Init. + * @param huart: Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval None + */ + __weak void HAL_UART_MspInit(UART_HandleTypeDef *huart) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(huart); + /* NOTE: This function should not be modified, when the callback is needed, + the HAL_UART_MspInit can be implemented in the user file + */ +} + +/** + * @brief UART MSP DeInit. + * @param huart: Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval None + */ + __weak void HAL_UART_MspDeInit(UART_HandleTypeDef *huart) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(huart); + /* NOTE: This function should not be modified, when the callback is needed, + the HAL_UART_MspDeInit can be implemented in the user file + */ +} + +/** + * @} + */ + +/** @defgroup UART_Exported_Functions_Group2 IO operation functions + * @brief UART Transmit and Receive functions + * +@verbatim + ============================================================================== + ##### IO operation functions ##### + ============================================================================== + [..] + This subsection provides a set of functions allowing to manage the UART asynchronous + and Half duplex data transfers. + + (#) There are two modes of transfer: + (++) Blocking mode: The communication is performed in polling mode. + The HAL status of all data processing is returned by the same function + after finishing transfer. + (++) Non blocking mode: The communication is performed using Interrupts + or DMA, these APIs return the HAL status. + The end of the data processing will be indicated through the + dedicated UART IRQ when using Interrupt mode or the DMA IRQ when + using DMA mode. + The HAL_UART_TxCpltCallback(), HAL_UART_RxCpltCallback() user callbacks + will be executed respectively at the end of the transmit or receive process. + The HAL_UART_ErrorCallback() user callback will be executed when + a communication error is detected. + + (#) Blocking mode APIs are: + (++) HAL_UART_Transmit() + (++) HAL_UART_Receive() + + (#) Non Blocking mode APIs with Interrupt are: + (++) HAL_UART_Transmit_IT() + (++) HAL_UART_Receive_IT() + (++) HAL_UART_IRQHandler() + + (#) Non Blocking mode functions with DMA are: + (++) HAL_UART_Transmit_DMA() + (++) HAL_UART_Receive_DMA() + (++) HAL_UART_DMAPause() + (++) HAL_UART_DMAResume() + (++) HAL_UART_DMAStop() + + (#) A set of Transfer Complete Callbacks are provided in non blocking mode: + (++) HAL_UART_TxHalfCpltCallback() + (++) HAL_UART_TxCpltCallback() + (++) HAL_UART_RxHalfCpltCallback() + (++) HAL_UART_RxCpltCallback() + (++) HAL_UART_ErrorCallback() + + [..] + (@) In the Half duplex communication, it is forbidden to run the transmit + and receive process in parallel, the UART state HAL_UART_STATE_BUSY_TX_RX + can't be useful. + +@endverbatim + * @{ + */ + +/** + * @brief Sends an amount of data in blocking mode. + * @param huart: Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @param pData: Pointer to data buffer + * @param Size: Amount of data to be sent + * @param Timeout: Timeout duration + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_Transmit(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size, uint32_t Timeout) +{ + uint16_t* tmp; + uint32_t tmp_state = 0; + + tmp_state = huart->State; + if((tmp_state == HAL_UART_STATE_READY) || (tmp_state == HAL_UART_STATE_BUSY_RX)) + { + if((pData == NULL) || (Size == 0)) + { + return HAL_ERROR; + } + + /* Process Locked */ + __HAL_LOCK(huart); + + huart->ErrorCode = HAL_UART_ERROR_NONE; + /* Check if a non-blocking receive process is ongoing or not */ + if(huart->State == HAL_UART_STATE_BUSY_RX) + { + huart->State = HAL_UART_STATE_BUSY_TX_RX; + } + else + { + huart->State = HAL_UART_STATE_BUSY_TX; + } + + huart->TxXferSize = Size; + huart->TxXferCount = Size; + while(huart->TxXferCount > 0) + { + huart->TxXferCount--; + if(huart->Init.WordLength == UART_WORDLENGTH_9B) + { + if(UART_WaitOnFlagUntilTimeout(huart, UART_FLAG_TXE, RESET, Timeout) != HAL_OK) + { + return HAL_TIMEOUT; + } + tmp = (uint16_t*) pData; + huart->Instance->DR = (*tmp & (uint16_t)0x01FF); + if(huart->Init.Parity == UART_PARITY_NONE) + { + pData +=2; + } + else + { + pData +=1; + } + } + else + { + if(UART_WaitOnFlagUntilTimeout(huart, UART_FLAG_TXE, RESET, Timeout) != HAL_OK) + { + return HAL_TIMEOUT; + } + huart->Instance->DR = (*pData++ & (uint8_t)0xFF); + } + } + + if(UART_WaitOnFlagUntilTimeout(huart, UART_FLAG_TC, RESET, Timeout) != HAL_OK) + { + return HAL_TIMEOUT; + } + + /* Check if a non-blocking receive process is ongoing or not */ + if(huart->State == HAL_UART_STATE_BUSY_TX_RX) + { + huart->State = HAL_UART_STATE_BUSY_RX; + } + else + { + huart->State = HAL_UART_STATE_READY; + } + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Receives an amount of data in blocking mode. + * @param huart: Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @param pData: Pointer to data buffer + * @param Size: Amount of data to be received + * @param Timeout: Timeout duration + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_Receive(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size, uint32_t Timeout) +{ + uint16_t* tmp; + uint32_t tmp_state = 0; + + tmp_state = huart->State; + if((tmp_state == HAL_UART_STATE_READY) || (tmp_state == HAL_UART_STATE_BUSY_TX)) + { + if((pData == NULL ) || (Size == 0)) + { + return HAL_ERROR; + } + + /* Process Locked */ + __HAL_LOCK(huart); + + huart->ErrorCode = HAL_UART_ERROR_NONE; + /* Check if a non-blocking transmit process is ongoing or not */ + if(huart->State == HAL_UART_STATE_BUSY_TX) + { + huart->State = HAL_UART_STATE_BUSY_TX_RX; + } + else + { + huart->State = HAL_UART_STATE_BUSY_RX; + } + + huart->RxXferSize = Size; + huart->RxXferCount = Size; + + /* Check the remain data to be received */ + while(huart->RxXferCount > 0) + { + huart->RxXferCount--; + if(huart->Init.WordLength == UART_WORDLENGTH_9B) + { + if(UART_WaitOnFlagUntilTimeout(huart, UART_FLAG_RXNE, RESET, Timeout) != HAL_OK) + { + return HAL_TIMEOUT; + } + tmp = (uint16_t*) pData ; + if(huart->Init.Parity == UART_PARITY_NONE) + { + *tmp = (uint16_t)(huart->Instance->DR & (uint16_t)0x01FF); + pData +=2; + } + else + { + *tmp = (uint16_t)(huart->Instance->DR & (uint16_t)0x00FF); + pData +=1; + } + + } + else + { + if(UART_WaitOnFlagUntilTimeout(huart, UART_FLAG_RXNE, RESET, Timeout) != HAL_OK) + { + return HAL_TIMEOUT; + } + if(huart->Init.Parity == UART_PARITY_NONE) + { + *pData++ = (uint8_t)(huart->Instance->DR & (uint8_t)0x00FF); + } + else + { + *pData++ = (uint8_t)(huart->Instance->DR & (uint8_t)0x007F); + } + + } + } + + /* Check if a non-blocking transmit process is ongoing or not */ + if(huart->State == HAL_UART_STATE_BUSY_TX_RX) + { + huart->State = HAL_UART_STATE_BUSY_TX; + } + else + { + huart->State = HAL_UART_STATE_READY; + } + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Sends an amount of data in non blocking mode. + * @param huart: Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @param pData: Pointer to data buffer + * @param Size: Amount of data to be sent + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_Transmit_IT(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size) +{ + uint32_t tmp_state = 0; + + tmp_state = huart->State; + if((tmp_state == HAL_UART_STATE_READY) || (tmp_state == HAL_UART_STATE_BUSY_RX)) + { + if((pData == NULL ) || (Size == 0)) + { + return HAL_ERROR; + } + + /* Process Locked */ + __HAL_LOCK(huart); + + huart->pTxBuffPtr = pData; + huart->TxXferSize = Size; + huart->TxXferCount = Size; + + huart->ErrorCode = HAL_UART_ERROR_NONE; + /* Check if a receive process is ongoing or not */ + if(huart->State == HAL_UART_STATE_BUSY_RX) + { + huart->State = HAL_UART_STATE_BUSY_TX_RX; + } + else + { + huart->State = HAL_UART_STATE_BUSY_TX; + } + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + /* Enable the UART Transmit data register empty Interrupt */ + __HAL_UART_ENABLE_IT(huart, UART_IT_TXE); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Receives an amount of data in non blocking mode + * @param huart: Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @param pData: Pointer to data buffer + * @param Size: Amount of data to be received + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_Receive_IT(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size) +{ + uint32_t tmp_state = 0; + + tmp_state = huart->State; + if((tmp_state == HAL_UART_STATE_READY) || (tmp_state == HAL_UART_STATE_BUSY_TX)) + { + if((pData == NULL ) || (Size == 0)) + { + return HAL_ERROR; + } + + /* Process Locked */ + __HAL_LOCK(huart); + + huart->pRxBuffPtr = pData; + huart->RxXferSize = Size; + huart->RxXferCount = Size; + + huart->ErrorCode = HAL_UART_ERROR_NONE; + /* Check if a transmit process is ongoing or not */ + if(huart->State == HAL_UART_STATE_BUSY_TX) + { + huart->State = HAL_UART_STATE_BUSY_TX_RX; + } + else + { + huart->State = HAL_UART_STATE_BUSY_RX; + } + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + /* Enable the UART Parity Error Interrupt */ + __HAL_UART_ENABLE_IT(huart, UART_IT_PE); + + /* Enable the UART Error Interrupt: (Frame error, noise error, overrun error) */ + __HAL_UART_ENABLE_IT(huart, UART_IT_ERR); + + /* Enable the UART Data Register not empty Interrupt */ + __HAL_UART_ENABLE_IT(huart, UART_IT_RXNE); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Sends an amount of data in non blocking mode. + * @param huart: Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @param pData: Pointer to data buffer + * @param Size: Amount of data to be sent + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_Transmit_DMA(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size) +{ + uint32_t *tmp; + uint32_t tmp_state = 0; + + tmp_state = huart->State; + if((tmp_state == HAL_UART_STATE_READY) || (tmp_state == HAL_UART_STATE_BUSY_RX)) + { + if((pData == NULL ) || (Size == 0)) + { + return HAL_ERROR; + } + + /* Process Locked */ + __HAL_LOCK(huart); + + huart->pTxBuffPtr = pData; + huart->TxXferSize = Size; + huart->TxXferCount = Size; + + huart->ErrorCode = HAL_UART_ERROR_NONE; + /* Check if a receive process is ongoing or not */ + if(huart->State == HAL_UART_STATE_BUSY_RX) + { + huart->State = HAL_UART_STATE_BUSY_TX_RX; + } + else + { + huart->State = HAL_UART_STATE_BUSY_TX; + } + + /* Set the UART DMA transfer complete callback */ + huart->hdmatx->XferCpltCallback = UART_DMATransmitCplt; + + /* Set the UART DMA Half transfer complete callback */ + huart->hdmatx->XferHalfCpltCallback = UART_DMATxHalfCplt; + + /* Set the DMA error callback */ + huart->hdmatx->XferErrorCallback = UART_DMAError; + + /* Enable the UART transmit DMA channel */ + tmp = (uint32_t*)&pData; + HAL_DMA_Start_IT(huart->hdmatx, *(uint32_t*)tmp, (uint32_t)&huart->Instance->DR, Size); + + /* Clear the TC flag in the SR register by writing 0 to it */ + __HAL_UART_CLEAR_FLAG(huart, UART_FLAG_TC); + + /* Enable the DMA transfer for transmit request by setting the DMAT bit + in the UART CR3 register */ + SET_BIT(huart->Instance->CR3, USART_CR3_DMAT); + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Receives an amount of data in non blocking mode. + * @param huart: Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @param pData: Pointer to data buffer + * @param Size: Amount of data to be received + * @note When the UART parity is enabled (PCE = 1), the received data contain + * the parity bit (MSB position) + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_Receive_DMA(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size) +{ + uint32_t *tmp; + uint32_t tmp_state = 0; + + tmp_state = huart->State; + if((tmp_state == HAL_UART_STATE_READY) || (tmp_state == HAL_UART_STATE_BUSY_TX)) + { + if((pData == NULL ) || (Size == 0)) + { + return HAL_ERROR; + } + + /* Process Locked */ + __HAL_LOCK(huart); + + huart->pRxBuffPtr = pData; + huart->RxXferSize = Size; + + huart->ErrorCode = HAL_UART_ERROR_NONE; + /* Check if a transmit process is ongoing or not */ + if(huart->State == HAL_UART_STATE_BUSY_TX) + { + huart->State = HAL_UART_STATE_BUSY_TX_RX; + } + else + { + huart->State = HAL_UART_STATE_BUSY_RX; + } + + /* Set the UART DMA transfer complete callback */ + huart->hdmarx->XferCpltCallback = UART_DMAReceiveCplt; + + /* Set the UART DMA Half transfer complete callback */ + huart->hdmarx->XferHalfCpltCallback = UART_DMARxHalfCplt; + + /* Set the DMA error callback */ + huart->hdmarx->XferErrorCallback = UART_DMAError; + + /* Enable the DMA channel */ + tmp = (uint32_t*)&pData; + HAL_DMA_Start_IT(huart->hdmarx, (uint32_t)&huart->Instance->DR, *(uint32_t*)tmp, Size); + + /* Enable the DMA transfer for the receiver request by setting the DMAR bit + in the UART CR3 register */ + SET_BIT(huart->Instance->CR3, USART_CR3_DMAR); + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Pauses the DMA Transfer. + * @param huart: Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_DMAPause(UART_HandleTypeDef *huart) +{ + /* Process Locked */ + __HAL_LOCK(huart); + + if(huart->State == HAL_UART_STATE_BUSY_TX) + { + /* Disable the UART DMA Tx request */ + CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAT); + } + else if(huart->State == HAL_UART_STATE_BUSY_RX) + { + /* Disable the UART DMA Rx request */ + CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAR); + } + else if (huart->State == HAL_UART_STATE_BUSY_TX_RX) + { + /* Disable the UART DMA Tx & Rx requests */ + CLEAR_BIT(huart->Instance->CR3, (USART_CR3_DMAT | USART_CR3_DMAR)); + } + else + { + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_ERROR; + } + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_OK; +} + +/** + * @brief Resumes the DMA Transfer. + * @param huart: Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_DMAResume(UART_HandleTypeDef *huart) +{ + /* Process Locked */ + __HAL_LOCK(huart); + + if(huart->State == HAL_UART_STATE_BUSY_TX) + { + /* Enable the UART DMA Tx request */ + SET_BIT(huart->Instance->CR3, USART_CR3_DMAT); + } + else if(huart->State == HAL_UART_STATE_BUSY_RX) + { + /* Clear the Overrun flag before resumming the Rx transfer*/ + __HAL_UART_CLEAR_OREFLAG(huart); + /* Enable the UART DMA Rx request */ + SET_BIT(huart->Instance->CR3, USART_CR3_DMAR); + } + else if(huart->State == HAL_UART_STATE_BUSY_TX_RX) + { + /* Clear the Overrun flag before resumming the Rx transfer*/ + __HAL_UART_CLEAR_OREFLAG(huart); + /* Enable the UART DMA Tx & Rx request */ + SET_BIT(huart->Instance->CR3, (USART_CR3_DMAT | USART_CR3_DMAR)); + } + else + { + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_ERROR; + } + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_OK; +} + +/** + * @brief Stops the DMA Transfer. + * @param huart: Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_DMAStop(UART_HandleTypeDef *huart) +{ + /* The Lock is not implemented on this API to allow the user application + to call the HAL UART API under callbacks HAL_UART_TxCpltCallback() / HAL_UART_RxCpltCallback(): + when calling HAL_DMA_Abort() API the DMA TX/RX Transfer complete interrupt is generated + and the correspond call back is executed HAL_UART_TxCpltCallback() / HAL_UART_RxCpltCallback() + */ + + /* Disable the UART Tx/Rx DMA requests */ + CLEAR_BIT(huart->Instance->CR3, (USART_CR3_DMAT | USART_CR3_DMAR)); + + /* Abort the UART DMA tx channel */ + if(huart->hdmatx != NULL) + { + HAL_DMA_Abort(huart->hdmatx); + } + /* Abort the UART DMA rx channel */ + if(huart->hdmarx != NULL) + { + HAL_DMA_Abort(huart->hdmarx); + } + + huart->State = HAL_UART_STATE_READY; + + return HAL_OK; +} + +/** + * @brief This function handles UART interrupt request. + * @param huart: Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval None + */ +void HAL_UART_IRQHandler(UART_HandleTypeDef *huart) +{ + uint32_t tmp_flag = 0, tmp_it_source = 0; + + tmp_flag = __HAL_UART_GET_FLAG(huart, UART_FLAG_PE); + tmp_it_source = __HAL_UART_GET_IT_SOURCE(huart, UART_IT_PE); + /* UART parity error interrupt occurred ------------------------------------*/ + if((tmp_flag != RESET) && (tmp_it_source != RESET)) + { + huart->ErrorCode |= HAL_UART_ERROR_PE; + } + + tmp_flag = __HAL_UART_GET_FLAG(huart, UART_FLAG_FE); + tmp_it_source = __HAL_UART_GET_IT_SOURCE(huart, UART_IT_ERR); + /* UART frame error interrupt occurred -------------------------------------*/ + if((tmp_flag != RESET) && (tmp_it_source != RESET)) + { + huart->ErrorCode |= HAL_UART_ERROR_FE; + } + + tmp_flag = __HAL_UART_GET_FLAG(huart, UART_FLAG_NE); + /* UART noise error interrupt occurred -------------------------------------*/ + if((tmp_flag != RESET) && (tmp_it_source != RESET)) + { + huart->ErrorCode |= HAL_UART_ERROR_NE; + } + + tmp_flag = __HAL_UART_GET_FLAG(huart, UART_FLAG_ORE); + /* UART Over-Run interrupt occurred ----------------------------------------*/ + if((tmp_flag != RESET) && (tmp_it_source != RESET)) + { + huart->ErrorCode |= HAL_UART_ERROR_ORE; + } + + tmp_flag = __HAL_UART_GET_FLAG(huart, UART_FLAG_RXNE); + tmp_it_source = __HAL_UART_GET_IT_SOURCE(huart, UART_IT_RXNE); + /* UART in mode Receiver ---------------------------------------------------*/ + if((tmp_flag != RESET) && (tmp_it_source != RESET)) + { + UART_Receive_IT(huart); + } + + tmp_flag = __HAL_UART_GET_FLAG(huart, UART_FLAG_TXE); + tmp_it_source = __HAL_UART_GET_IT_SOURCE(huart, UART_IT_TXE); + /* UART in mode Transmitter ------------------------------------------------*/ + if((tmp_flag != RESET) && (tmp_it_source != RESET)) + { + UART_Transmit_IT(huart); + } + + tmp_flag = __HAL_UART_GET_FLAG(huart, UART_FLAG_TC); + tmp_it_source = __HAL_UART_GET_IT_SOURCE(huart, UART_IT_TC); + /* UART in mode Transmitter end --------------------------------------------*/ + if((tmp_flag != RESET) && (tmp_it_source != RESET)) + { + UART_EndTransmit_IT(huart); + } + + if(huart->ErrorCode != HAL_UART_ERROR_NONE) + { + /* Clear all the error flag at once */ + __HAL_UART_CLEAR_PEFLAG(huart); + + /* Set the UART state ready to be able to start again the process */ + huart->State = HAL_UART_STATE_READY; + + HAL_UART_ErrorCallback(huart); + } +} + +/** + * @brief Tx Transfer completed callbacks. + * @param huart: Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval None + */ + __weak void HAL_UART_TxCpltCallback(UART_HandleTypeDef *huart) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(huart); + /* NOTE: This function should not be modified, when the callback is needed, + the HAL_UART_TxCpltCallback can be implemented in the user file + */ +} + +/** + * @brief Tx Half Transfer completed callbacks. + * @param huart: Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval None + */ + __weak void HAL_UART_TxHalfCpltCallback(UART_HandleTypeDef *huart) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(huart); + /* NOTE: This function should not be modified, when the callback is needed, + the HAL_UART_TxHalfCpltCallback can be implemented in the user file + */ +} + +/** + * @brief Rx Transfer completed callbacks. + * @param huart: Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval None + */ +__weak void HAL_UART_RxCpltCallback(UART_HandleTypeDef *huart) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(huart); + /* NOTE: This function should not be modified, when the callback is needed, + the HAL_UART_RxCpltCallback can be implemented in the user file + */ +} + +/** + * @brief Rx Half Transfer completed callbacks. + * @param huart: Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval None + */ +__weak void HAL_UART_RxHalfCpltCallback(UART_HandleTypeDef *huart) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(huart); + /* NOTE: This function should not be modified, when the callback is needed, + the HAL_UART_RxHalfCpltCallback can be implemented in the user file + */ +} + +/** + * @brief UART error callbacks. + * @param huart: Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval None + */ + __weak void HAL_UART_ErrorCallback(UART_HandleTypeDef *huart) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(huart); + /* NOTE: This function should not be modified, when the callback is needed, + the HAL_UART_ErrorCallback can be implemented in the user file + */ +} + +/** + * @} + */ + +/** @defgroup UART_Exported_Functions_Group3 Peripheral Control functions + * @brief UART control functions + * +@verbatim + ============================================================================== + ##### Peripheral Control functions ##### + ============================================================================== + [..] + This subsection provides a set of functions allowing to control the UART: + (+) HAL_LIN_SendBreak() API can be helpful to transmit the break character. + (+) HAL_MultiProcessor_EnterMuteMode() API can be helpful to enter the UART in mute mode. + (+) HAL_MultiProcessor_ExitMuteMode() API can be helpful to exit the UART mute mode by software. + (+) HAL_HalfDuplex_EnableTransmitter() API to enable the UART transmitter and disables the UART receiver in Half Duplex mode + (+) HAL_HalfDuplex_EnableReceiver() API to enable the UART receiver and disables the UART transmitter in Half Duplex mode + +@endverbatim + * @{ + */ + +/** + * @brief Transmits break characters. + * @param huart: Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_LIN_SendBreak(UART_HandleTypeDef *huart) +{ + /* Check the parameters */ + assert_param(IS_UART_INSTANCE(huart->Instance)); + + /* Process Locked */ + __HAL_LOCK(huart); + + huart->State = HAL_UART_STATE_BUSY; + + /* Send break characters */ + SET_BIT(huart->Instance->CR1, USART_CR1_SBK); + + huart->State = HAL_UART_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_OK; +} + +/** + * @brief Enters the UART in mute mode. + * @param huart: Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_MultiProcessor_EnterMuteMode(UART_HandleTypeDef *huart) +{ + /* Check the parameters */ + assert_param(IS_UART_INSTANCE(huart->Instance)); + + /* Process Locked */ + __HAL_LOCK(huart); + + huart->State = HAL_UART_STATE_BUSY; + + /* Enable the USART mute mode by setting the RWU bit in the CR1 register */ + SET_BIT(huart->Instance->CR1, USART_CR1_RWU); + + huart->State = HAL_UART_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_OK; +} + +/** + * @brief Exits the UART mute mode: wake up software. + * @param huart: Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_MultiProcessor_ExitMuteMode(UART_HandleTypeDef *huart) +{ + /* Check the parameters */ + assert_param(IS_UART_INSTANCE(huart->Instance)); + + /* Process Locked */ + __HAL_LOCK(huart); + + huart->State = HAL_UART_STATE_BUSY; + + /* Disable the USART mute mode by clearing the RWU bit in the CR1 register */ + CLEAR_BIT(huart->Instance->CR1, USART_CR1_RWU); + + huart->State = HAL_UART_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_OK; +} + +/** + * @brief Enables the UART transmitter and disables the UART receiver. + * @param huart: Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_HalfDuplex_EnableTransmitter(UART_HandleTypeDef *huart) +{ + /* Process Locked */ + __HAL_LOCK(huart); + + huart->State = HAL_UART_STATE_BUSY; + + /*-------------------------- USART CR1 Configuration -----------------------*/ + /* Clear TE and RE bits */ + /* Enable the USART's transmit interface by setting the TE bit in the USART CR1 register */ + MODIFY_REG(huart->Instance->CR1, (uint32_t)(USART_CR1_TE | USART_CR1_RE), USART_CR1_TE); + + huart->State = HAL_UART_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_OK; +} + +/** + * @brief Enables the UART receiver and disables the UART transmitter. + * @param huart: Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_HalfDuplex_EnableReceiver(UART_HandleTypeDef *huart) +{ + /* Process Locked */ + __HAL_LOCK(huart); + + huart->State = HAL_UART_STATE_BUSY; + + /*-------------------------- USART CR1 Configuration -----------------------*/ + /* Clear TE and RE bits */ + /* Enable the USART's receive interface by setting the RE bit in the USART CR1 register */ + MODIFY_REG(huart->Instance->CR1, (uint32_t)(USART_CR1_TE | USART_CR1_RE), USART_CR1_RE); + + huart->State = HAL_UART_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_OK; +} + +/** + * @} + */ + +/** @defgroup UART_Exported_Functions_Group4 Peripheral State and Errors functions + * @brief UART State and Errors functions + * +@verbatim + ============================================================================== + ##### Peripheral State and Errors functions ##### + ============================================================================== + [..] + This subsection provides a set of functions allowing to return the State of + UART communication process, return Peripheral Errors occurred during communication + process + (+) HAL_UART_GetState() API can be helpful to check in run-time the state of the UART peripheral. + (+) HAL_UART_GetError() check in run-time errors that could be occurred during communication. + +@endverbatim + * @{ + */ + +/** + * @brief Returns the UART state. + * @param huart: Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL state + */ +HAL_UART_StateTypeDef HAL_UART_GetState(UART_HandleTypeDef *huart) +{ + return huart->State; +} + +/** +* @brief Return the UART error code +* @param huart: Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART. +* @retval UART Error Code +*/ +uint32_t HAL_UART_GetError(UART_HandleTypeDef *huart) +{ + return huart->ErrorCode; +} + +/** + * @} + */ + +/** + * @} + */ + +/** @defgroup UART_Private_Functions UART Private Functions + * @brief UART Private functions + * @{ + */ +/** + * @brief DMA UART transmit process complete callback. + * @param hdma: Pointer to a DMA_HandleTypeDef structure that contains + * the configuration information for the specified DMA module. + * @retval None + */ +static void UART_DMATransmitCplt(DMA_HandleTypeDef *hdma) +{ + UART_HandleTypeDef* huart = ( UART_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent; + /* DMA Normal mode*/ + if ( HAL_IS_BIT_CLR(hdma->Instance->CCR, DMA_CCR_CIRC) ) + { + huart->TxXferCount = 0; + + /* Disable the DMA transfer for transmit request by setting the DMAT bit + in the UART CR3 register */ + CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAT); + + /* Enable the UART Transmit Complete Interrupt */ + __HAL_UART_ENABLE_IT(huart, UART_IT_TC); + } + /* DMA Circular mode */ + else + { + HAL_UART_TxCpltCallback(huart); + } +} + +/** + * @brief DMA UART transmit process half complete callback + * @param hdma: Pointer to a DMA_HandleTypeDef structure that contains + * the configuration information for the specified DMA module. + * @retval None + */ +static void UART_DMATxHalfCplt(DMA_HandleTypeDef *hdma) +{ + UART_HandleTypeDef* huart = (UART_HandleTypeDef*)((DMA_HandleTypeDef*)hdma)->Parent; + + HAL_UART_TxHalfCpltCallback(huart); +} + +/** + * @brief DMA UART receive process complete callback. + * @param hdma: Pointer to a DMA_HandleTypeDef structure that contains + * the configuration information for the specified DMA module. + * @retval None + */ +static void UART_DMAReceiveCplt(DMA_HandleTypeDef *hdma) +{ + UART_HandleTypeDef* huart = ( UART_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent; + /* DMA Normal mode*/ + if ( HAL_IS_BIT_CLR(hdma->Instance->CCR, DMA_CCR_CIRC) ) + { + huart->RxXferCount = 0; + + /* Disable the DMA transfer for the receiver request by setting the DMAR bit + in the UART CR3 register */ + CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAR); + + /* Check if a transmit process is ongoing or not */ + if(huart->State == HAL_UART_STATE_BUSY_TX_RX) + { + huart->State = HAL_UART_STATE_BUSY_TX; + } + else + { + huart->State = HAL_UART_STATE_READY; + } + } + HAL_UART_RxCpltCallback(huart); +} + +/** + * @brief DMA UART receive process half complete callback + * @param hdma: Pointer to a DMA_HandleTypeDef structure that contains + * the configuration information for the specified DMA module. + * @retval None + */ +static void UART_DMARxHalfCplt(DMA_HandleTypeDef *hdma) +{ + UART_HandleTypeDef* huart = (UART_HandleTypeDef*)((DMA_HandleTypeDef*)hdma)->Parent; + + HAL_UART_RxHalfCpltCallback(huart); +} + +/** + * @brief DMA UART communication error callback. + * @param hdma: Pointer to a DMA_HandleTypeDef structure that contains + * the configuration information for the specified DMA module. + * @retval None + */ +static void UART_DMAError(DMA_HandleTypeDef *hdma) +{ + UART_HandleTypeDef* huart = ( UART_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent; + huart->RxXferCount = 0; + huart->TxXferCount = 0; + huart->State= HAL_UART_STATE_READY; + huart->ErrorCode |= HAL_UART_ERROR_DMA; + HAL_UART_ErrorCallback(huart); +} + +/** + * @brief This function handles UART Communication Timeout. + * @param huart: Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @param Flag: specifies the UART flag to check. + * @param Status: The new Flag status (SET or RESET). + * @param Timeout: Timeout duration + * @retval HAL status + */ +static HAL_StatusTypeDef UART_WaitOnFlagUntilTimeout(UART_HandleTypeDef *huart, uint32_t Flag, FlagStatus Status, uint32_t Timeout) +{ + uint32_t tickstart = 0; + + /* Get tick */ + tickstart = HAL_GetTick(); + + /* Wait until flag is set */ + if(Status == RESET) + { + while(__HAL_UART_GET_FLAG(huart, Flag) == RESET) + { + /* Check for the Timeout */ + if(Timeout != HAL_MAX_DELAY) + { + if((Timeout == 0)||((HAL_GetTick() - tickstart ) > Timeout)) + { + /* Disable TXE, RXNE, PE and ERR (Frame error, noise error, overrun error) interrupts for the interrupt process */ + __HAL_UART_DISABLE_IT(huart, UART_IT_TXE); + __HAL_UART_DISABLE_IT(huart, UART_IT_RXNE); + __HAL_UART_DISABLE_IT(huart, UART_IT_PE); + __HAL_UART_DISABLE_IT(huart, UART_IT_ERR); + + huart->State= HAL_UART_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_TIMEOUT; + } + } + } + } + else + { + while(__HAL_UART_GET_FLAG(huart, Flag) != RESET) + { + /* Check for the Timeout */ + if(Timeout != HAL_MAX_DELAY) + { + if((Timeout == 0)||((HAL_GetTick() - tickstart ) > Timeout)) + { + /* Disable TXE, RXNE, PE and ERR (Frame error, noise error, overrun error) interrupts for the interrupt process */ + __HAL_UART_DISABLE_IT(huart, UART_IT_TXE); + __HAL_UART_DISABLE_IT(huart, UART_IT_RXNE); + __HAL_UART_DISABLE_IT(huart, UART_IT_PE); + __HAL_UART_DISABLE_IT(huart, UART_IT_ERR); + + huart->State= HAL_UART_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_TIMEOUT; + } + } + } + } + return HAL_OK; +} + +/** + * @brief Sends an amount of data in non blocking mode. + * @param huart: Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +static HAL_StatusTypeDef UART_Transmit_IT(UART_HandleTypeDef *huart) +{ + uint16_t* tmp; + uint32_t tmp_state = 0; + + tmp_state = huart->State; + if((tmp_state == HAL_UART_STATE_BUSY_TX) || (tmp_state == HAL_UART_STATE_BUSY_TX_RX)) + { + if(huart->Init.WordLength == UART_WORDLENGTH_9B) + { + tmp = (uint16_t*) huart->pTxBuffPtr; + huart->Instance->DR = (uint16_t)(*tmp & (uint16_t)0x01FF); + if(huart->Init.Parity == UART_PARITY_NONE) + { + huart->pTxBuffPtr += 2; + } + else + { + huart->pTxBuffPtr += 1; + } + } + else + { + huart->Instance->DR = (uint8_t)(*huart->pTxBuffPtr++ & (uint8_t)0x00FF); + } + + if(--huart->TxXferCount == 0) + { + /* Disable the UART Transmit Complete Interrupt */ + __HAL_UART_DISABLE_IT(huart, UART_IT_TXE); + + /* Enable the UART Transmit Complete Interrupt */ + __HAL_UART_ENABLE_IT(huart, UART_IT_TC); + } + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + + +/** + * @brief Wraps up transmission in non blocking mode. + * @param huart: pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +static HAL_StatusTypeDef UART_EndTransmit_IT(UART_HandleTypeDef *huart) +{ + /* Disable the UART Transmit Complete Interrupt */ + __HAL_UART_DISABLE_IT(huart, UART_IT_TC); + + /* Check if a receive process is ongoing or not */ + if(huart->State == HAL_UART_STATE_BUSY_TX_RX) + { + huart->State = HAL_UART_STATE_BUSY_RX; + } + else + { + huart->State = HAL_UART_STATE_READY; + } + + HAL_UART_TxCpltCallback(huart); + + return HAL_OK; +} + +/** + * @brief Receives an amount of data in non blocking mode + * @param huart: Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +static HAL_StatusTypeDef UART_Receive_IT(UART_HandleTypeDef *huart) +{ + uint16_t* tmp; + uint32_t tmp_state = 0; + + tmp_state = huart->State; + if((tmp_state == HAL_UART_STATE_BUSY_RX) || (tmp_state == HAL_UART_STATE_BUSY_TX_RX)) + { + if(huart->Init.WordLength == UART_WORDLENGTH_9B) + { + tmp = (uint16_t*) huart->pRxBuffPtr; + if(huart->Init.Parity == UART_PARITY_NONE) + { + *tmp = (uint16_t)(huart->Instance->DR & (uint16_t)0x01FF); + huart->pRxBuffPtr += 2; + } + else + { + *tmp = (uint16_t)(huart->Instance->DR & (uint16_t)0x00FF); + huart->pRxBuffPtr += 1; + } + } + else + { + if(huart->Init.Parity == UART_PARITY_NONE) + { + *huart->pRxBuffPtr++ = (uint8_t)(huart->Instance->DR & (uint8_t)0x00FF); + } + else + { + *huart->pRxBuffPtr++ = (uint8_t)(huart->Instance->DR & (uint8_t)0x007F); + } + } + + if(--huart->RxXferCount == 0) + { + __HAL_UART_DISABLE_IT(huart, UART_IT_RXNE); + + /* Check if a transmit process is ongoing or not */ + if(huart->State == HAL_UART_STATE_BUSY_TX_RX) + { + huart->State = HAL_UART_STATE_BUSY_TX; + } + else + { + /* Disable the UART Parity Error Interrupt */ + __HAL_UART_DISABLE_IT(huart, UART_IT_PE); + + /* Disable the UART Error Interrupt: (Frame error, noise error, overrun error) */ + __HAL_UART_DISABLE_IT(huart, UART_IT_ERR); + + huart->State = HAL_UART_STATE_READY; + } + HAL_UART_RxCpltCallback(huart); + + return HAL_OK; + } + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Configures the UART peripheral. + * @param huart: Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval None + */ +static void UART_SetConfig(UART_HandleTypeDef *huart) +{ + uint32_t tmpreg = 0x00; + + /* Check the parameters */ + assert_param(IS_UART_BAUDRATE(huart->Init.BaudRate)); + assert_param(IS_UART_STOPBITS(huart->Init.StopBits)); + assert_param(IS_UART_PARITY(huart->Init.Parity)); + assert_param(IS_UART_MODE(huart->Init.Mode)); + + /*------- UART-associated USART registers setting : CR2 Configuration ------*/ + /* Configure the UART Stop Bits: Set STOP[13:12] bits according + * to huart->Init.StopBits value */ + MODIFY_REG(huart->Instance->CR2, USART_CR2_STOP, huart->Init.StopBits); + + /*------- UART-associated USART registers setting : CR1 Configuration ------*/ + /* Configure the UART Word Length, Parity and mode: + Set the M bits according to huart->Init.WordLength value + Set PCE and PS bits according to huart->Init.Parity value + Set TE and RE bits according to huart->Init.Mode value */ + tmpreg = (uint32_t)huart->Init.WordLength | huart->Init.Parity | huart->Init.Mode ; + MODIFY_REG(huart->Instance->CR1, + (uint32_t)(USART_CR1_M | USART_CR1_PCE | USART_CR1_PS | USART_CR1_TE | USART_CR1_RE), + tmpreg); + + /*------- UART-associated USART registers setting : CR3 Configuration ------*/ + /* Configure the UART HFC: Set CTSE and RTSE bits according to huart->Init.HwFlowCtl value */ + MODIFY_REG(huart->Instance->CR3, (USART_CR3_RTSE | USART_CR3_CTSE), huart->Init.HwFlowCtl); + + /*------- UART-associated USART registers setting : BRR Configuration ------*/ + if((huart->Instance == USART1)) + { + huart->Instance->BRR = UART_BRR_SAMPLING16(HAL_RCC_GetPCLK2Freq(), huart->Init.BaudRate); + } + else + { + huart->Instance->BRR = UART_BRR_SAMPLING16(HAL_RCC_GetPCLK1Freq(), huart->Init.BaudRate); + } +} +/** + * @} + */ + +#endif /* HAL_UART_MODULE_ENABLED */ +/** + * @} + */ + +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/stm32cubemx/Inc/stm32f1xx_hal_conf.h b/stm32cubemx/Inc/stm32f1xx_hal_conf.h index da282bb..ec25522 100644 --- a/stm32cubemx/Inc/stm32f1xx_hal_conf.h +++ b/stm32cubemx/Inc/stm32f1xx_hal_conf.h @@ -79,7 +79,7 @@ /*#define HAL_SPI_MODULE_ENABLED */ /*#define HAL_SRAM_MODULE_ENABLED */ #define HAL_TIM_MODULE_ENABLED -/*#define HAL_UART_MODULE_ENABLED */ +#define HAL_UART_MODULE_ENABLED /*#define HAL_USART_MODULE_ENABLED */ /*#define HAL_WWDG_MODULE_ENABLED */ diff --git a/stm32cubemx/Src/main.c b/stm32cubemx/Src/main.c index 7c5f9d3..f57b555 100644 --- a/stm32cubemx/Src/main.c +++ b/stm32cubemx/Src/main.c @@ -53,6 +53,8 @@ TIM_HandleTypeDef htim1; DMA_HandleTypeDef hdma_tim1_ch1; +UART_HandleTypeDef huart2; + /* USER CODE BEGIN PV */ /* Private variables ---------------------------------------------------------*/ @@ -64,7 +66,7 @@ void Error_Handler(void); static void MX_GPIO_Init(void); static void MX_DMA_Init(void); static void MX_TIM1_Init(void); -static void MX_NVIC_Init(void); +static void MX_USART2_UART_Init(void); /* USER CODE BEGIN PFP */ /* Private function prototypes -----------------------------------------------*/ @@ -95,9 +97,7 @@ int main(void) MX_DMA_Init(); MX_TIM1_Init(); MX_USB_DEVICE_Init(); - - /* Initialize interrupts */ - MX_NVIC_Init(); + MX_USART2_UART_Init(); /* USER CODE BEGIN 2 */ main_post_init(); @@ -172,15 +172,6 @@ void SystemClock_Config(void) HAL_NVIC_SetPriority(SysTick_IRQn, 0, 0); } -/** NVIC Configuration -*/ -static void MX_NVIC_Init(void) -{ - /* TIM1_TRG_COM_IRQn interrupt configuration */ - HAL_NVIC_SetPriority(TIM1_TRG_COM_IRQn, 1, 0); - HAL_NVIC_EnableIRQ(TIM1_TRG_COM_IRQn); -} - /* TIM1 init function */ static void MX_TIM1_Init(void) { @@ -191,7 +182,7 @@ static void MX_TIM1_Init(void) htim1.Instance = TIM1; htim1.Init.Prescaler = RX_TIMER_PRESCALER; htim1.Init.CounterMode = TIM_COUNTERMODE_UP; - htim1.Init.Period = 0; + htim1.Init.Period = 65535; htim1.Init.ClockDivision = TIM_CLOCKDIVISION_DIV1; htim1.Init.RepetitionCounter = 0; if (HAL_TIM_IC_Init(&htim1) != HAL_OK) @@ -217,6 +208,25 @@ static void MX_TIM1_Init(void) } +/* USART2 init function */ +static void MX_USART2_UART_Init(void) +{ + + huart2.Instance = USART2; + huart2.Init.BaudRate = 115200; + huart2.Init.WordLength = UART_WORDLENGTH_8B; + huart2.Init.StopBits = UART_STOPBITS_1; + huart2.Init.Parity = UART_PARITY_NONE; + huart2.Init.Mode = UART_MODE_TX_RX; + huart2.Init.HwFlowCtl = UART_HWCONTROL_NONE; + huart2.Init.OverSampling = UART_OVERSAMPLING_16; + if (HAL_UART_Init(&huart2) != HAL_OK) + { + Error_Handler(); + } + +} + /** * Enable DMA controller clock */ diff --git a/stm32cubemx/Src/stm32f1xx_hal_msp.c b/stm32cubemx/Src/stm32f1xx_hal_msp.c index eefddb9..b90d153 100644 --- a/stm32cubemx/Src/stm32f1xx_hal_msp.c +++ b/stm32cubemx/Src/stm32f1xx_hal_msp.c @@ -125,6 +125,11 @@ void HAL_TIM_IC_MspInit(TIM_HandleTypeDef* htim_ic) __HAL_LINKDMA(htim_ic,hdma[TIM_DMA_ID_CC1],hdma_tim1_ch1); + /* Peripheral interrupt init */ + HAL_NVIC_SetPriority(TIM1_TRG_COM_IRQn, 1, 0); + HAL_NVIC_EnableIRQ(TIM1_TRG_COM_IRQn); + HAL_NVIC_SetPriority(TIM1_CC_IRQn, 1, 0); + HAL_NVIC_EnableIRQ(TIM1_CC_IRQn); /* USER CODE BEGIN TIM1_MspInit 1 */ /* USER CODE END TIM1_MspInit 1 */ @@ -154,6 +159,8 @@ void HAL_TIM_IC_MspDeInit(TIM_HandleTypeDef* htim_ic) /* Peripheral interrupt DeInit*/ HAL_NVIC_DisableIRQ(TIM1_TRG_COM_IRQn); + HAL_NVIC_DisableIRQ(TIM1_CC_IRQn); + } /* USER CODE BEGIN TIM1_MspDeInit 1 */ @@ -161,6 +168,63 @@ void HAL_TIM_IC_MspDeInit(TIM_HandleTypeDef* htim_ic) } +void HAL_UART_MspInit(UART_HandleTypeDef* huart) +{ + + GPIO_InitTypeDef GPIO_InitStruct; + if(huart->Instance==USART2) + { + /* USER CODE BEGIN USART2_MspInit 0 */ + + /* USER CODE END USART2_MspInit 0 */ + /* Peripheral clock enable */ + __HAL_RCC_USART2_CLK_ENABLE(); + + /**USART2 GPIO Configuration + PA2 ------> USART2_TX + PA3 ------> USART2_RX + */ + GPIO_InitStruct.Pin = GPIO_PIN_2; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + GPIO_InitStruct.Pin = GPIO_PIN_3; + GPIO_InitStruct.Mode = GPIO_MODE_INPUT; + GPIO_InitStruct.Pull = GPIO_NOPULL; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + /* USER CODE BEGIN USART2_MspInit 1 */ + + /* USER CODE END USART2_MspInit 1 */ + } + +} + +void HAL_UART_MspDeInit(UART_HandleTypeDef* huart) +{ + + if(huart->Instance==USART2) + { + /* USER CODE BEGIN USART2_MspDeInit 0 */ + + /* USER CODE END USART2_MspDeInit 0 */ + /* Peripheral clock disable */ + __HAL_RCC_USART2_CLK_DISABLE(); + + /**USART2 GPIO Configuration + PA2 ------> USART2_TX + PA3 ------> USART2_RX + */ + HAL_GPIO_DeInit(GPIOA, GPIO_PIN_2|GPIO_PIN_3); + + } + /* USER CODE BEGIN USART2_MspDeInit 1 */ + + /* USER CODE END USART2_MspDeInit 1 */ + +} + /* USER CODE BEGIN 1 */ /* USER CODE END 1 */ diff --git a/stm32cubemx/Src/stm32f1xx_it.c b/stm32cubemx/Src/stm32f1xx_it.c index 83f5436..ac5d604 100644 --- a/stm32cubemx/Src/stm32f1xx_it.c +++ b/stm32cubemx/Src/stm32f1xx_it.c @@ -242,6 +242,20 @@ void TIM1_TRG_COM_IRQHandler(void) /* USER CODE END TIM1_TRG_COM_IRQn 1 */ } +/** +* @brief This function handles TIM1 capture compare interrupt. +*/ +void TIM1_CC_IRQHandler(void) +{ + /* USER CODE BEGIN TIM1_CC_IRQn 0 */ + it_tim1(); + /* USER CODE END TIM1_CC_IRQn 0 */ + HAL_TIM_IRQHandler(&htim1); + /* USER CODE BEGIN TIM1_CC_IRQn 1 */ + + /* USER CODE END TIM1_CC_IRQn 1 */ +} + /* USER CODE BEGIN 1 */ /* USER CODE END 1 */ diff --git a/stm32cubemx/stm32cubemx.gpdsc b/stm32cubemx/stm32cubemx.gpdsc index d484a1e..fc4d497 100644 --- a/stm32cubemx/stm32cubemx.gpdsc +++ b/stm32cubemx/stm32cubemx.gpdsc @@ -1,7 +1,7 @@ <?xml version="1.0" encoding="UTF-8" standalone="no"?> <!-- ****************************************************************************** * File Name : stm32cubemx.gpdsc - * Date : 30/04/2017 20:16:12 + * Date : 12/05/2017 00:08:30 * Description : Generator PDSC File generated by STM32CubeMX (DO NOT EDIT!) ****************************************************************************** --> @@ -11,22 +11,22 @@ <description>STM32CubeMX generated pack description</description> <releases> <release version="1.0.0"> - - Generated: 30/04/2017 20:16:12 + - Generated: 12/05/2017 00:08:30 </release> </releases> <requirements> <languages> <language name="C" version="99"/> <language name="C++" version="11"/> - </languages> + </languages> </requirements> <create> <project> <options> - <stack size="0x400"/> + <stack size="0x400"/> <heap size="0x200"/> <debugProbe name="ST-Link" protocol="swd"/> - </options> + </options> </project> </create> <generators> @@ -75,7 +75,7 @@ <files> </files> </component> - <component Cclass="Device" Cgroup="Startup" Cversion="2.1.0"> + <component Cclass="Device" Cgroup="Startup" Cversion="2.1.0"> <description>System Startup for STMicroelectronics</description> <files> <file category="header" name="Drivers\CMSIS\Device\ST\STM32F1xx\Include\stm32f1xx.h"/> @@ -129,6 +129,13 @@ <file category="source" name="Drivers\STM32F1xx_HAL_Driver\Src\stm32f1xx_hal_tim_ex.c"/> </files> </component> + <component Cclass="Device" Cgroup="STM32Cube HAL" Csub="UART" Cversion="0.0.1"> + <description></description> + <files> + <file category="header" name="Drivers\STM32F1xx_HAL_Driver\Inc\stm32f1xx_hal_uart.h"/> + <file category="source" name="Drivers\STM32F1xx_HAL_Driver\Src\stm32f1xx_hal_uart.c"/> + </files> + </component> <component Cclass="Device" Cgroup="STM32Cube HAL" Csub="COMMON" Cversion="0.3.0"> <description></description> <files> diff --git a/stm32cubemx/stm32cubemx.ioc b/stm32cubemx/stm32cubemx.ioc index 06e173a..3ea18c9 100644 --- a/stm32cubemx/stm32cubemx.ioc +++ b/stm32cubemx/stm32cubemx.ioc @@ -18,24 +18,27 @@ Mcu.IP1=NVIC Mcu.IP2=RCC Mcu.IP3=SYS Mcu.IP4=TIM1 -Mcu.IP5=USB -Mcu.IP6=USB_DEVICE -Mcu.IPNb=7 +Mcu.IP5=USART2 +Mcu.IP6=USB +Mcu.IP7=USB_DEVICE +Mcu.IPNb=8 Mcu.Name=STM32F103C(4-6)Tx Mcu.Package=LQFP48 Mcu.Pin0=PC14-OSC32_IN Mcu.Pin1=PC15-OSC32_OUT -Mcu.Pin10=VP_USB_DEVICE_VS_USB_DEVICE_CDC_FS +Mcu.Pin10=PA14 +Mcu.Pin11=VP_SYS_VS_Systick +Mcu.Pin12=VP_USB_DEVICE_VS_USB_DEVICE_CDC_FS Mcu.Pin2=PD0-OSC_IN Mcu.Pin3=PD1-OSC_OUT -Mcu.Pin4=PA8 -Mcu.Pin5=PA11 -Mcu.Pin6=PA12 -Mcu.Pin7=PA13 -Mcu.Pin8=PA14 -Mcu.Pin9=VP_SYS_VS_Systick -Mcu.PinsNb=11 -Mcu.UserConstants=RX_TIMER_PRESCALER,(72000000 / 2000) +Mcu.Pin4=PA2 +Mcu.Pin5=PA3 +Mcu.Pin6=PA8 +Mcu.Pin7=PA11 +Mcu.Pin8=PA12 +Mcu.Pin9=PA13 +Mcu.PinsNb=13 +Mcu.UserConstants=RX_TIMER_PRESCALER,(72000000 / 72000) Mcu.UserName=STM32F103C6Tx MxCube.Version=4.20.1 MxDb.Version=DB.4.0.200 @@ -49,7 +52,8 @@ NVIC.PendSV_IRQn=true\:0\:0\:false\:false\:true NVIC.PriorityGroup=NVIC_PRIORITYGROUP_4 NVIC.SVCall_IRQn=true\:0\:0\:false\:false\:true NVIC.SysTick_IRQn=true\:0\:0\:true\:false\:true -NVIC.TIM1_TRG_COM_IRQn=true\:1\:0\:true\:true\:true\:1 +NVIC.TIM1_CC_IRQn=true\:1\:0\:true\:false\:true +NVIC.TIM1_TRG_COM_IRQn=true\:1\:0\:true\:false\:true NVIC.USB_HP_CAN1_TX_IRQn=true\:0\:0\:false\:false\:true NVIC.USB_LP_CAN1_RX0_IRQn=true\:0\:0\:false\:false\:true NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:true @@ -61,6 +65,10 @@ PA13.Mode=Serial_Wire PA13.Signal=SYS_JTMS-SWDIO PA14.Mode=Serial_Wire PA14.Signal=SYS_JTCK-SWCLK +PA2.Mode=Asynchronous +PA2.Signal=USART2_TX +PA3.Mode=Asynchronous +PA3.Signal=USART2_RX PA8.Signal=S_TIM1_CH1 PC14-OSC32_IN.Mode=LSE-External-Oscillator PC14-OSC32_IN.Signal=RCC_OSC32_IN @@ -103,7 +111,7 @@ ProjectManager.StackSize=0x400 ProjectManager.TargetToolchain=Other Toolchains (GPDSC) ProjectManager.ToolChainLocation= ProjectManager.UnderRoot=false -ProjectManager.functionlistsort=1-MX_GPIO_Init-GPIO-false-HAL,2-MX_DMA_Init-DMA-false-HAL,3-SystemClock_Config-RCC-false-HAL,4-MX_TIM1_Init-TIM1-false-HAL,5-MX_USB_DEVICE_Init-USB_DEVICE-false-HAL +ProjectManager.functionlistsort=1-MX_GPIO_Init-GPIO-false-HAL,2-MX_DMA_Init-DMA-false-HAL,3-SystemClock_Config-RCC-false-HAL,4-MX_TIM1_Init-TIM1-false-HAL,5-MX_USB_DEVICE_Init-USB_DEVICE-false-HAL,6-MX_USART2_UART_Init-USART2-false-HAL RCC.ADCFreqValue=36000000 RCC.AHBFreq_Value=72000000 RCC.APB1CLKDivider=RCC_HCLK_DIV2 @@ -129,8 +137,11 @@ RCC.VCOOutput2Freq_Value=8000000 SH.S_TIM1_CH1.0=TIM1_CH1,Input_Capture1_from_TI1 SH.S_TIM1_CH1.ConfNb=1 TIM1.Channel-Input_Capture1_from_TI1=TIM_CHANNEL_1 -TIM1.IPParameters=Channel-Input_Capture1_from_TI1,Prescaler +TIM1.IPParameters=Channel-Input_Capture1_from_TI1,Prescaler,Period +TIM1.Period=65535 TIM1.Prescaler=RX_TIMER_PRESCALER +USART2.IPParameters=VirtualMode +USART2.VirtualMode=VM_ASYNC USB_DEVICE.CLASS_NAME_FS=CDC USB_DEVICE.IPParameters=VirtualMode,VirtualModeFS,CLASS_NAME_FS USB_DEVICE.VirtualMode=Cdc |