o Moving tinyprintf and stm libraries under thirdparty.

1 files changed, 0 insertions, 111 deletions

diff --git a/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/RTC/LSI_Calib/readme.txt b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/RTC/LSI_Calib/readme.txt
deleted file mode 100644
index f465c39..0000000
--- a/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/RTC/LSI_Calib/readme.txt
+++ /dev/null
@@ -1,111 +0,0 @@
-
-/**
-  @page RTC_LSI_Calib RTC LSI_Calib example
-  
-  @verbatim
-  ******************** (C) COPYRIGHT 2011 STMicroelectronics *******************
-  * @file    RTC/LSI_Calib/readme.txt 
-  * @author  MCD Application Team
-  * @version V3.5.0
-  * @date    08-April-2011
-  * @brief   Description of the RTC LSI_Calib example.
-  ******************************************************************************
-  * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
-  * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
-  * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
-  * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
-  * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
-  * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
-  ******************************************************************************
-   @endverbatim
-
-@par Example Description 
-
-This example demonstrates and explains how to use the LSI clock source auto
-calibration to get a precise RTC clock. 
-As an application example, it demonstrates how to configure the TIM5 timer
-internally connected to LSI clock output, in order to adjust the RTC prescaler. 
-
-The Low Speed External (LSI) clock is used as RTC clock source.
-After reset, the RTC prescaler is set with the default value (40000). 
-The inaccuracy of the LSI clock causes the RTC Second signal to be inaccurate. This
-signal is output on the Tamper pin (PC.13) and can be measured by on oscilloscope
-or a frequencymeter.
-
-The program waits until Key Push button is pressed to begin the auto calibration procedure:
- - Configure the TIM5 to remap internally the TIM5 Channel 4 Input Capture to the
-   LSI clock output.
- - Enable the TIM5 Input Capture interrupt: after one cycle of LSI clock, the
-   period value is stored in a variable and compared to the HCLK clock to get
-   its real value.
- - The RTC prescaler is adjusted with this LSI frequency value so that the RTC
-   Second value become more accurate.
- - When calibration is done a led connected to PF.07 is turned ON to indicate the
-    end of this operation. At this moment, you can  monitor the Second signal on
-    an oscilloscope to measure its accuracy again.
-
-The RTC Second signal can be monitored either on Tamper pin or on LED1 which is 
-toggled into the RTC Second interrupt service routine.
-    
- 
-@par Directory contents 
-
-  - RTC/LSI_Calib/stm32f10x_conf.h     Library Configuration file
-  - RTC/LSI_Calib/stm32f10x_it.c       Interrupt handlers
-  - RTC/LSI_Calib/stm32f10x_it.h       Header for stm32f10x_it.c
-  - RTC/LSI_Calib/main.h               Main header file
-  - RTC/LSI_Calib/main.c               Main program
-  - RTC/LSI_Calib/system_stm32f10x.c   STM32F10x system source file
-  
-@par Hardware and Software environment 
-
-  - This example runs on STM32F10x Connectivity line, High-Density Value line,
-    High-Density and XL-Density Devices.
-  
-  - This example has been tested with STMicroelectronics STM32100E-EVAL (High-Density 
-    Value line), STM3210E-EVAL (High-Density and XL-Density) and STM3210C-EVAL 
-    (Connectivity Line) evaluation boards and can be easily tailored to any other 
-    supported device and development board.
-    To select the STMicroelectronics evaluation board used to run the example, 
-    uncomment the corresponding line in stm32_eval.h file (under Utilities\STM32_EVAL)
-
-  - STM32100E-EVAL Set-up 
-    - Use LD1 and LD2 leds connected respectively to PF.06 and PF.07 pins
-    - Use the Key push button connected to PG.08 pin
-    
-  - STM3210C-EVAL Set-up 
-    - Use LD1 and LD2 leds connected respectively to PD.07 and PD.13 pins
-    - Use the Key push-button connected to PB.09 pin
-
-  - STM3210E-EVAL Set-up 
-    - Use LD1 and LD2 leds connected respectively to PF.06 and PF.07 pins
-    - Use the Key push button connected to PG.08 pin
-
-@par How to use it ? 
-
-In order to make the program work, you must do the following :
- - Copy all source files from this example folder to the template folder under
-   Project\STM32F10x_StdPeriph_Template
- - Open your preferred toolchain 
- - Rebuild all files and load your image into target memory
- - Run the example
-
-@note
- - Low-density Value line devices are STM32F100xx microcontrollers where the 
-   Flash memory density ranges between 16 and 32 Kbytes.
- - Low-density devices are STM32F101xx, STM32F102xx and STM32F103xx 
-   microcontrollers where the Flash memory density ranges between 16 and 32 Kbytes.
- - Medium-density Value line devices are STM32F100xx microcontrollers where
-   the Flash memory density ranges between 64 and 128 Kbytes.  
- - Medium-density devices are STM32F101xx, STM32F102xx and STM32F103xx 
-   microcontrollers where the Flash memory density ranges between 64 and 128 Kbytes.
- - High-density Value line devices are STM32F100xx microcontrollers where
-   the Flash memory density ranges between 256 and 512 Kbytes.
- - High-density devices are STM32F101xx and STM32F103xx microcontrollers where
-   the Flash memory density ranges between 256 and 512 Kbytes.
- - XL-density devices are STM32F101xx and STM32F103xx microcontrollers where
-   the Flash memory density ranges between 512 and 1024 Kbytes.
- - Connectivity line devices are STM32F105xx and STM32F107xx microcontrollers.
-   
- * <h3><center>&copy; COPYRIGHT 2011 STMicroelectronics</center></h3>
- */