summaryrefslogtreecommitdiff
path: root/tcl/target
Commit message (Collapse)AuthorAgeFilesLines
...
* Remove srst_pulls_trst from LPC2148 targetPeter Stuge2010-08-011-1/+1
| | | | | | | | | srst_pulls_trst is only true on some (broken) LPC2148 boards, a fact which is already documented in doc/openocd.texi, so it shouldn't be set unconditionally in the target tcl. This patch was needed to reflash when an Abort exception occured very early after reset, before OpenOCD tried to halt the CPU.
* lpc7168: make flash available upon reset initØyvind Harboe2010-07-301-0/+19
| | | | | | | set user mode to avoid ROM being mapped at address 0 rather than flash. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* lm3s811-ek uses generic stellaris target configDavid Brownell2010-07-171-29/+0
| | | | | | | There's no point in an lm3s811-specific target file, so remove it in favor of the generic "stellaris.cfg". Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* cfg: add Avalue RSC-W910 configSpencer Oliver2010-07-131-0/+27
| | | | Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* at91sam3s* supportOlaf Lüke2010-06-253-36/+73
| | | | Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* DM36x: pll & clock setupThomas Koeller2010-06-151-0/+127
| | | | | | | | Added a function 'pll_v03_setup' to set up PLLs and clock dividers on DM365 and DM368. Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com> Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* arm1136 scriptsmichal smulski2010-06-151-1/+2
| | | | | | | | | Here is a patch to fix a startup in C100 (arm1136). Basically make sure that UART is configured before using it. Michal Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* cfg: add pic32 virtual banksSpencer Oliver2010-05-261-0/+7
| | | | | | make use of the new virtual bank flash driver. Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* There are no variants of arm7tdmi targetFreddie Chopin2010-05-247-7/+7
| | | | Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* All LPC2xxx chips are little endian and that cannot be changed - update ↵Freddie Chopin2010-05-247-53/+8
| | | | | | config scripts Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* add correct CPUTAPID value for LPC2129Freddie Chopin2010-05-241-6/+2
| | | | Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* Update "flash bank" helper comments for LPC2xxx chipsFreddie Chopin2010-05-248-7/+8
| | | | Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* LPC23xx and LPC24xx after reset run on internal 4MHz RC oscillator, so ↵Freddie Chopin2010-05-241-1/+1
| | | | | | "flash bank" parameter should be 4000 (not 12000) Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* at91sam9260: use RCLKØyvind Harboe2010-05-211-19/+12
| | | | | | | | | | | | | It might be possible to get this target going without RCLK, but it would require more careful analysis and usage of the reset events. Enable fast memory accesses. Tested on an at91sam9260 custom board w/external DRAM and flash. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* at91rm9200 : reset_config should go to the board config fileMarc Pignat2010-05-181-2/+0
| | | | | | Let other boards do other things with srst and trst. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* scripts: update flash bank namesSpencer Oliver2010-05-136-12/+12
| | | | | | As the flash bank name is now unique update the scripts to suit. Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* telo: update configuration scripts to matched master branchmichal smulski2010-04-243-64/+3
| | | | Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* TCL scripts: update to current "flash bank" syntaxAntonio Borneo2010-03-261-1/+1
| | | | | | | | | | | | | | While "flash bank" syntax has been changed long ago, several tcl script are still not fully update. Fix following cases related with "cfi" driver: - syntax error: the mandatory <name> parameter is missing - warning: the <target> parameter is a number, instead of the target name - the comment line above the command does not report actual syntax Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
* PIC32: add Microchip Explorer16 cfgSpencer Oliver2010-03-161-4/+1
| | | | | | | - add Microchip Explorer16 cfg using PIC32MX360F512L PIM. - remove reset config from PIC32 target cfg. Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* rename jtag_nsrst_assert_width as adapter_nsrst_assert_widthDavid Brownell2010-03-151-1/+1
| | | | | | | | | | | Globally rename "jtag_nsrst_assert_width" as "adapter_nsrst_assert_width", and move it out of the "jtag" command group ... it needs to be used with non-JTAG transports Includes a migration aid (in jtag/startup.tcl) so that old user scripts won't break. That aid should Sunset in about a year. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* rename jtag_nsrst_delay as adapter_nsrst_delayDavid Brownell2010-03-1534-36/+36
| | | | | | | | | | | Globally rename "jtag_nsrst_delay" as "adapter_nsrst_delay", and move it out of the "jtag" command group ... it needs to be used with non-JTAG transports Includes a migration aid (in jtag/startup.tcl) so that old user scripts won't break. That aid should Sunset in about a year. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* rename jtag_khz as adapter_khzDavid Brownell2010-03-1518-35/+35
| | | | | | | | | | | Globally rename "jtag_khz" as "adapter_khz", and move it out of the "jtag" command group ... it needs to be used with non-JTAG transports Includes a migration aid (in jtag/startup.tcl) so that old user scripts won't break. That aid should Sunset in about a year. (We may want to update it to include a nag message too.) Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* PIC32MX: update cfg scriptSpencer Oliver2010-03-151-10/+23
| | | | | | | | The default config script will now dynamically setup the BMX registers in the reset init script. This will also work if the user overrides the default working area. Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* PIC32: add flash algorithm supportSpencer Oliver2010-03-101-4/+12
| | | | | | | | | | | | | Add flash algorithm support for the PIC32MX. Still a few things todo but this dramatically decreases the programing time, eg. approx programming for 2.5k test file. - without fastload: 60secs - with fastload: 45secs - with fastload and algorithm: 2secs. Add new devices to supported list. Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* LPC1768 updates, IAR board supportDavid Brownell2010-03-021-25/+27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix some issues with the generic LPC1768 config file: - Handle the post-reset clock config: 4 MHz internal RC, no PLL. This affects flash and JTAG clocking. - Remove JTAG adapter config; they don't all support trst_and_srst - Remove the rest of the bogus "reset-init" event handler. - Allow explicit CCLK configuration, instead of assuming 12 MHz; some boards will use 100 Mhz (or the post-reset 4 MHz). - Simplify: rely on defaults for endianness and IR-Capture value - Update some comments too Build on those fixes to make a trivial config for the IAR LPC1768 kickstart board (by Olimex) start working. Also, add doxygen to the lpc2000 flash driver, primarily to note a configuration problem with driver: it wrongly assumes the core clock rate never changes. Configs that are safe for updating flash after "reset halt" will thus often be unsafe later ... e.g. for LPC1768, after switching to use PLL0 at 100 MHz. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* Add target/mc13224v.cfgMariano Alvira2010-02-271-0/+54
| | | | | | | | | | | | | | | | | The MC13224V is a FreeScale ARM7TDMI based IEEE802.15.4 platform for Zigbee and similar low-power wireless applications. Using PIP (Platform In Package) technology, it integrates: an RF balun and matching network; a buck converter (only an external inductor is necessary); 96KB of SRAM; and 128KB of non-volatile memory. It has an integrated bootloader and can boot from a variety of sources: external SPI or I2C non-volatile memory, an image loaded over UART1, or the internal non-volatile memory. The image loaded from one of these sources is executed directly from SRAM starting at location 0x00400000. Open source development code at http://mc1322x.devl.org Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* LPC1768.cfg -- partial fixes for bogus reset-init handlerDavid Brownell2010-02-151-4/+4
| | | | | | | | | Cortex-M targets don't support ARM instructions. Leave the NVIC.VTOR setup alone, but comment how the whole routine looks like one big bug... Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* target library: configuration files for openocd tested with Atmel SAM-ICE V6 ↵Viktar Palstsiuk2010-02-111-0/+44
| | | | | | JTAG. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* str730.cfg: fix incorrect mem regionsSpencer Oliver2010-02-091-2/+2
| | | | | | - update str73x mem regions to correct values. Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* scripts: Phytec/LPC2350 config scriptsEthan Eade2010-02-041-0/+36
| | | | Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* AT91R40008/Ethernut 3 configurationHarald Kipp2010-02-021-32/+9
| | | | | | | | | | Moved board specific settings from target/at91r40008.cfg to a new file board/ethernut3.cfg. Set correct CPUTAPID. Reset delay increased, see MIC2775 data sheet. Increased work area size from 16k to 128k. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* tcl/str7x: Reset init unlocks the flashEdgar Grimberg2010-02-022-2/+17
| | | | | | | | | | | For STR7x flash, the device cannot be queried for the protect status. The solution is to remove the protection on reset init. The driver also initialises the sector protect field to unprotected. [dbrownell@users.sourceforge.net: line length shrinkage] Signed-off-by: Edgar Grimberg <edgar.grimberg@zylin.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* flash/str7x: After reset init the flash is unlockedEdgar Grimberg2010-02-021-1/+9
| | | | | | | | | | | | | | The default state of the STR7 flash after a reset init is unlocked. The information in the flash driver now reflects this. The information about the lock status cannot be read from the flash chip, so the user is informed that flash info might not contain accurate information. [dbrownell@users.sourceforge.net: line length shrinkage] Signed-off-by: Edgar Grimberg <edgar.grimberg@zylin.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* tcl/target/at91sam3u4e.cfg: changed case in dependent fileMichael Grzeschik2010-01-201-1/+1
| | | | | | | | openocd does not start with the target configfile due to the case in the dependent config file. Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* PIC32: enable ram executionSpencer Oliver2010-01-051-1/+17
| | | | | | add reset-init script to allow ram execution from reset, this is required for ejtag fastdata access. Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* target.cfg: update to use new flash configuration syntaxSpencer Oliver2009-12-1711-15/+15
| | | | Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* more tcl/{board,target} cleanupDavid Brownell2009-12-155-7/+7
| | | | | | | | | | | | | | Remove more remnants of the old "jtag_device" syntax. Don't [format "%s.cpu" $_CHIPNAME] ... it's needless complexity. Remove various non-supported "-variant" target options; they're not needed often at all. Flag some of the board files as needing to have and use target files for the TAP and target declarations. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* testing/examples/.../*cfg: rm jtag_device callsDavid Brownell2009-12-151-3/+0
| | | | | | | That syntax has been obsolete forever and is now gone; remove a few remaining references. Shows how seldom this stuff gets used. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* target: add basic dsp563xx supportmkdorg@users.sourceforge.net2009-12-151-0/+38
|
* imx31: move srst delay into config scriptØyvind Harboe2009-12-151-0/+2
| | | | | | reset init/run now works again. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* lm3748: use new Stellaris config fileDavid Brownell2009-12-141-29/+0
| | | | | | Use the new file, and remove the old target/lm3s3748.cfg one. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* Common target file for Stellaris chipsYegor Yefremov2009-12-141-0/+49
| | | | | | | | | Common target.cfg file for LM3S CPU family [dbrownell@users.sourceforge.net: rename, generalize more] Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* OMAP2420: define reset-assert eventDavid Brownell2009-12-071-0/+7
| | | | | | | | | Behave like OMAP3530: force global software reset. Given the patch to teach ARM11 how to use these events, and use VCR to catch the reset vector, this works better than either the current reset logic or than using SRST. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* Tcl and doc: update to match new 'arm mcr ...' etcDavid Brownell2009-12-012-5/+5
| | | | | | Make them match the C code. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* target: at91eb40a.cfg is a board, not a target.Øyvind Harboe2009-12-011-62/+0
| | | | | | | Also updated to use target name when creating flash and set jtag_khz to 16000. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* create target/pxa3xx.cfgMarek Vasut2009-11-291-0/+86
| | | | | | [dbrownell@users.sourceforge.net; remove pxa255 comment] Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* omap3530.cfg: use new "reset-assert" eventDavid Brownell2009-11-271-2/+2
| | | | | | Replaces previous "reset-assert-pre" workaround. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* omap3530.cfg: yes we have SRAM!David Brownell2009-11-251-0/+3
| | | | Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* target.cfg: TAP id for Hilscher netX 500David Brownell2009-11-201-9/+7
| | | | | | Based on email from "Martin Kaul <martin.kaul@leuze.de>". Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* update 'flash bank' usage in scriptsZachary T Welch2009-11-1939-45/+90
| | | | | Sets $_FLASHNAME to "$_CHIPNAME.flash" and passes it as the first argument to 'flash bank'.