summaryrefslogtreecommitdiff
path: root/tcl
Commit message (Collapse)AuthorAgeFilesLines
* initial builds of OSK5912 boards need srst_pulls_trstDavid Brownell2009-10-081-0/+4
| | | | | | | | | | | | This is clearly noted in the hardware spec (section 5.2.3); it works around a chip erratum: "If the MPU_RESET signal is used, it may cause the EMIFS bus to lock." I seem to have a board with such an initial build. The chip is labeled XOMAP. Presumably, parts without that "X" prefix (eXperimental) resolve this. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* make OMAP5912 resets more reliableDavid Brownell2009-10-071-0/+2
| | | | | | | Without some extra delay after releasing SRST, we seemed to be trying to talk to the TAP before it was ready to respond. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* iMX25 target supportJohn Rigby2009-10-071-0/+41
| | | | Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* first stab at imx35 reset init scriptoharboe2009-10-071-0/+272
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@2817 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* remove recrusive reset invocation from reset init callbackoharboe2009-10-071-5/+0
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@2816 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Add basic support for DM6446 EVM board.dbrownell2009-10-061-0/+74
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@2808 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Dragonite target scriptdbrownell2009-10-061-0/+31
| | | | | | | From: Nicolas Pitre <nico@fluxnic.net> git-svn-id: svn://svn.berlios.de/openocd/trunk@2806 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* stop using targetnumoharboe2009-10-061-1/+1
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@2804 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Add a new JTAG "setup" event; use for better DaVinci ICEpick support.dbrownell2009-10-053-21/+28
| | | | | | | | | | | | | | | | | The model is that this fires after scanchain verification, when it's safe to call "jtag tapenable $TAPNAME". So it will fire as part of non-error paths of "init" and "reset" command processing. However it will *NOT* trigger during "jtag_reset" processing, which skips all scan chain verification, or after verification errors. ALSO: - switch DaVinci chips to use this new mechanism - log TAP activation/deactivation, since their IDCODEs aren't verified - unify "enum jtag_event" scripted event notifications - remove duplicative JTAG_TAP_EVENT_POST_RESET git-svn-id: svn://svn.berlios.de/openocd/trunk@2800 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Get rid of needless OMAP and Davinci target config optionsdbrownell2009-10-055-38/+13
| | | | | | | so they provide better examples and are easier to maintain. git-svn-id: svn://svn.berlios.de/openocd/trunk@2797 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Updated reset event handling in omap3530 cfgmlu2009-10-021-2/+7
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@2796 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Remove annoying EOL whitespace (again, sigh).dbrownell2009-09-307-69/+69
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@2781 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* strip gdb config optionsoharboe2009-09-302-9/+0
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@2779 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* michal smulski <michal.smulski@ooma.com> reset now worksoharboe2009-09-303-67/+212
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@2778 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Don't provide invalid OMAP5912 IR capture value/mask attributesdbrownell2009-09-271-3/+3
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@2762 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* On DM355 EVM board, associate NAND chips with $_TARGETNAMEdbrownell2009-09-261-2/+2
| | | | | | | instead of a target number. git-svn-id: svn://svn.berlios.de/openocd/trunk@2761 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Update DM355 target config to know about ICEpick.dbrownell2009-09-251-5/+18
| | | | | | | Still defaults to nonstandard EMU0/EMU1 settings. git-svn-id: svn://svn.berlios.de/openocd/trunk@2757 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Michael Hasselberg <mh@open-engineering.de> target configuration files for ↵oharboe2009-09-254-0/+355
| | | | | | Toshiba TX09 familiy git-svn-id: svn://svn.berlios.de/openocd/trunk@2756 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Remove annoying end-of-line whitespace from tcl/* filesdbrownell2009-09-2185-683/+682
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@2743 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Ethan Eade <ethan@evolution.com> board config script for Cogent CSB732 ↵oharboe2009-09-211-0/+71
| | | | | | i.MX35 (arm1136) git-svn-id: svn://svn.berlios.de/openocd/trunk@2741 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Ensure that DaVinci chips can't start with a too-fast JTAG clock.dbrownell2009-09-213-0/+18
| | | | | | | | | | It can be sped up later, once it's known the PLLs are active. Note that modern tools from TI all use adaptive clocking; and that if that's done with OpenOCD, "too fast" is also a non-issue. git-svn-id: svn://svn.berlios.de/openocd/trunk@2740 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Reduced sleep time after reset mlu2009-09-191-1/+2
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@2732 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Move Cortex A8 debug access initialisation from omap3530.cfg to cortex_a8.cmlu2009-09-181-18/+3
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@2728 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Rolf Meeser <rolfm_9dq@yahoo.de> adds flash support for NXP's LPC2900 family ↵oharboe2009-09-162-0/+170
| | | | | | (ARM968E). git-svn-id: svn://svn.berlios.de/openocd/trunk@2715 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Magnus Lundin <lundin@mlu.mine.nu> Disable poll while core register ↵oharboe2009-09-131-0/+2
| | | | | | initialization git-svn-id: svn://svn.berlios.de/openocd/trunk@2703 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* David Brownell <david-b@pacbell.net> oharboe2009-09-123-4/+96
| | | | | | | | | | | | | | Update the board config for the DaVinci DM355 EVM so the reset-init event handler does the rest of the work it should do: - minor PLL setup bugfixes - initialize the DDR2 controller - probe both NAND banks - initialize UART0 - enable the icache git-svn-id: svn://svn.berlios.de/openocd/trunk@2699 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* tap post reset event added. Allows omap3530 to send 100 runtest idle ↵oharboe2009-09-111-0/+2
| | | | | | tickle's after a TAP_RESET. git-svn-id: svn://svn.berlios.de/openocd/trunk@2696 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* - revert change made to sheevaplug.cfg in rev2573ntfreak2009-09-111-1/+1
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@2695 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* syntax error fixoharboe2009-09-111-0/+1
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@2689 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* michal smulski <michal.smulski@ooma.com> telo target/board scriptsoharboe2009-09-105-30/+1396
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@2683 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* use "armv4_5 core_state arm" instead of soft_reset_halt, fewer side effectsoharboe2009-09-043-4/+5
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@2672 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Dirk Behme <dirk.behme@googlemail.com> retire jtag_speed usageoharboe2009-09-041-2/+0
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@2671 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Dirk Behme <dirk.behme@googlemail.com> Add default fall back freqency.oharboe2009-09-041-0/+3
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@2670 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* set ARM mode using explicit command rather than soft_reset_halt which has ↵oharboe2009-09-041-1/+1
| | | | | | lots of side effects. git-svn-id: svn://svn.berlios.de/openocd/trunk@2669 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* David Brownell <david-b@pacbell.net> "set _TARGETNAME ..." cleanupoharboe2009-09-0445-49/+54
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@2665 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* David Claffey <dnclaffey@gmail.com> get rid of reset recursionoharboe2009-09-041-3/+4
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@2664 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* David Claffey <dnclaffey@gmail.com> tested with the Atheros reference design ↵oharboe2009-09-021-0/+56
| | | | | | "PB44" git-svn-id: svn://svn.berlios.de/openocd/trunk@2662 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Crusty Code fixes from the tcl directory re-arragementsduane2009-09-023-22/+22
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@2661 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Gary Carlson <gcarlson@carlson-minot.com> config fileoharboe2009-08-311-0/+204
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@2657 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Ferdinand Postema <ferdinand@postema.eu> config script for the MMnet1001 ↵oharboe2009-08-311-0/+83
| | | | | | module from Propox. git-svn-id: svn://svn.berlios.de/openocd/trunk@2656 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* David Brownell <david-b@pacbell.net> The Stellaris eval boards don't have ↵oharboe2009-08-284-6/+0
| | | | | | | | | | | TRST signals, so defining ntrst_delay is pointless; don't. At least the LM3S3748 eval board doesn't need nsrst_delay either; remove that too. git-svn-id: svn://svn.berlios.de/openocd/trunk@2645 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Ferdinand Postema <ferdinand@postema.eu> increase reset delay to fix ↵oharboe2009-08-251-1/+1
| | | | | | regression from 2600 to 2604 git-svn-id: svn://svn.berlios.de/openocd/trunk@2614 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Brian Findlay <findlaybrian@gmail.com> finalize mini2440.cfgoharboe2009-08-251-3/+2
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@2611 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* use cortex_a8 instead of cortex_m3oharboe2009-08-251-3/+1
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@2610 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Pieter Conradie <Pieter.Conradie@psitek.com> shuffle things around to the ↵oharboe2009-08-214-129/+5
| | | | | | right spots. Should have been done in previous commit. git-svn-id: svn://svn.berlios.de/openocd/trunk@2604 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* native line endingsoharboe2009-08-215-284/+284
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@2603 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Pieter Conradie <Pieter.Conradie@psitek.com> Scripts for Atmel AT91SAM7S256 ↵oharboe2009-08-215-0/+284
| | | | | | and AT91SAM9260 git-svn-id: svn://svn.berlios.de/openocd/trunk@2602 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Brian Findlay <findlaybrian@gmail.com> Board support for mini2440 ↵oharboe2009-08-181-0/+321
| | | | | | (friendlyARM) samsung s3c2440 based board git-svn-id: svn://svn.berlios.de/openocd/trunk@2593 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* - add cfg file for Amontec JTAGKey2 jtag interfacentfreak2009-08-181-0/+11
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@2592 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* David Brownell <david-b@pacbell.net> Cleanup the Stellaris target configs:oharboe2009-08-185-59/+21
| | | | | | | | | | | | | | | | - remove endianness options; these chips hard-wire "little" - $_TARGETNAME updates: * don't pass $_TARGETNAME where a TAP label is required * flash config uses $_TARGETNAME (it might not be target #0) * simplify one $_TARGETNAME construction - update work area setup: * remove VM spec; these chips have no VM! * fix some wrong sizes (0x4000 == 16K, not 4K) * simplify: take defaults - comment fixups git-svn-id: svn://svn.berlios.de/openocd/trunk@2589 b42882b7-edfa-0310-969c-e2dbd0fdcd60
generated by cgit v1.2.3 (git 2.46.0) at 2024-11-09 06:25:23 +0000